What to do if my Raymarine Monitor shows no depth reading or lost bottom lock?
If your Raymarine Monitor shows no depth reading or has lost bottom lock, check the transducer location to ensure it's installed correctly. Also, verify the transducer angle, adjusting if it's too great. If the transducer has a kick-up mechanism, ensure it hasn't kicked up. Check the power supply voltage under load, and inspect the transducer for damage or fouling.
Why does my Raymarine Monitor not turn on or keep turning off?
Your Raymarine Monitor might not be turning on or keeps turning off due to several reasons: a blown fuse or tripped breaker (check and replace if necessary, and inspect for cable damage if fuses repeatedly blow), a poor or damaged power supply cable or connections (ensure the cable is fully inserted and locked, check for damage or corrosion, and flex the cable to check for reboots), incorrect power connection (ensure the installation instructions have been followed), or an insufficient power source (check the power supply voltage under load).
What to do if my Raymarine Monitor displays a “No Fix” GPS status icon?
If your Raymarine Monitor displays a 'No Fix' GPS status icon, it could be due to your geographic location or prevailing conditions preventing a satellite fix (check periodically in better conditions or another location), a GPS connection fault (ensure external GPS connections and cabling are correct), or an external GPS antenna in a poor position (ensure the GPS antenna has a clear view of the sky).
What to do if my Raymarine Monitor will not boot up (re-boot loop)?
If your Raymarine Monitor will not boot up, it could be due to the power supply and connection issues. Also, in the unlikely event that the product's software has become corrupted, please try re-flashing the latest software from the Raymarine website. On display products, as a last resort, you can try to perform a ‘Power on Reset’; however, this will delete all settings/presets and user data and revert the unit back to factory defaults.
What does it mean if my Raymarine Monitor displays 'No Data' or 'No scanner message'?
If your Raymarine Monitor displays 'No Data' or 'No scanner message', check the scanner power supply cable to ensure it's sound and connections are tight and free from corrosion. Also, check that the scanner is correctly connected to a Raymarine network switch or SeaTalkhs crossover coupler, as applicable. Ensure the scanner pedestal switch is in the ON position.
How to fix a Raymarine Monitor radar that will not initialize (Voltage control module (VCM) stuck in “sleep mode”)?
If your Raymarine Monitor radar will not initialize because the Voltage Control Module (VCM) is stuck in 'sleep mode', check the power connection at the VCM. Ensure the voltage at the input is 12/24V and the voltage at the output is 40V.
Why does my Raymarine Marine GPS System say “No Fix”?
If the Raymarine Marine GPS System displays a “No Fix” GPS status icon, it could be due to several reasons. First, geographic location or prevailing conditions might be preventing a satellite fix; check periodically to see if a fix is obtained in better conditions or another geographic location. Second, there may be a GPS connection fault; ensure that external GPS connections and cabling are correct and fault free. Third, the external GPS antenna might be in a poor position; ensure it has a clear view of the sky.
What to do if Raymarine Marine GPS System won't boot up?
If your Raymarine Marine GPS System product will not boot up or is in a re-boot loop, first refer to the solutions for 'Product does not turn on or keeps turning off'. If the issue persists, it could be due to software corruption. Try re-flashing the latest software from the Raymarine website. As a last resort, on display products, you can try to perform a ‘Power on Reset’; however, this will delete all settings/presets and user data (such as waypoints and tracks) and revert the unit back to factory defaults.
How do I fix a Raymarine Marine GPS System with no depth reading?
If your Raymarine Marine GPS System is showing no depth reading or has lost bottom lock, there are several potential causes. Check that the transducer has been installed in accordance with the instructions provided with it. If the transducer angle is too great, the beam can miss the bottom, so adjust the transducer angle and recheck. If the transducer has a kick-up mechanism, check that it has not kicked up due to hitting an object. With the product under load, use a multi-meter to check the power supply voltage as close to the unit as possible to establish the actual voltage when the current is flowing.
How do I correct the bearing on my Raymarine Marine GPS System radar?
If the bearing of a target on the radar screen of your Raymarine Marine GPS System is incorrect, the radar bearing alignment likely requires correcting. Check and adjust the radar bearing alignment.
General| Brand | Raymarine |
|---|---|
| Model | eS75 |
| Category | Marine GPS System |
| Language | English |
Provides crucial safety advice for navigational judgment and reliance on official charts.
Highlights the importance of user-defined settings for route generation safety.
Warns users not to solely rely on automatic route generation and to review routes carefully.
Advises against using automatic route generation near traffic separation schemes.
Ensures personnel are clear of the scanner during radar transmission.
Provides safety precautions for sonar operation, including avoiding use outside water.
Recommends avoiding touchscreen use in prolonged direct sunlight due to heat.
Advises on touchscreen performance in rain and how to handle it.
Details the procedure for powering the display on, off, and enabling PowerSave mode.
Covers touchscreen cursor movement, locking, and unlocking.
Describes the Homescreen layout and icons for touch-only displays.
Explains the Homescreen layout for HybridTouch and non-touch displays.
Guides through the startup wizard and additional initial setup tasks.
Explains how to enable autopilot control for SeaTalk/SPX and Evolution autopilots.
Describes how to display and identify engine data, including running the identification wizard.
Details the steps to enable AIS unit connection and configuration.
Describes how to check for and install software updates for Raymarine products.
Details how to save waypoints, routes, tracks, and system settings to a memory card.
Lists data items and settings that can be saved to and restored from a memory card.
Explains how to perform a system reset to factory defaults, including data reset.
Explains how to select external sensors and devices for data display.
Lists options for configuring connected external devices like autopilots and cameras.
Provides access to Bluetooth and Wi-Fi functions for device connectivity.
Provides detailed information on the display and connected equipment for troubleshooting.
Provides an overview of Raymarine autopilot control capabilities via MFD.
Details how to enable autopilot control for SeaTalk/SPX and Evolution autopilots.
Explains how to engage the autopilot using the pilot button or chart application.
Describes methods to disengage the autopilot via Power button, Shortcuts or Pilot button.
Guides through the Pilot Set-up page for Evolution autopilot configuration.
Details pilot settings including Vessel Settings, Drive Settings, and Commissioning.
Covers the procedures for commissioning an Evolution autopilot system.
Explains how autopilot alarms are displayed, silenced, and managed.
Provides an overview of alarms, their severity coding, and acknowledgment.
Explains how to configure alarms, manage activity, and view history.
Details configuration options for Safety, General, Switch Panel, and Engine alarms.
Describes how to activate and cancel the Man Overboard (MOB) function.
Details how to enable AIS overlay in Chart and Radar applications.
Describes Target interception features to improve collision awareness.
Provides an overview of the chart application's navigation features and views.
Lists navigation options like Goto Cursor, Goto Waypoint, Follow Route, and Start Track.
Describes Radar and Chart features to increase collision awareness.
Provides an overview of the Fishfinder application, its features, and sonar technologies.
Details types of sonar crosstalk interference and methods to reduce it.
Covers sensitivity settings for Gain, Contrast, Noise Filter, and Color Threshold.
Details how to set up Fish, Fishfinder Deep, and Fishfinder Shallow alarms.
Describes how to reset the sonar unit to its factory default values.
Provides an overview of the Radar application, its features, and important safety advice.
Describes Radar and Chart features to increase collision awareness.
Explains MARPA functionality for collision awareness by tracking targets.
Guides on setting up a Guard Zone Alarm to alert for radar returns within a specified zone.
Guides on how to reset radar settings to their default values.
Guides on changing datapage order, content, and adding new custom datapages.
Describes how to display and identify engine data, including running the identification wizard.
Guides on setting up and checking the thermal camera's main functions and image adjustments.
Guides on setting up and checking the thermal camera's main functions and image adjustments.
Guides on connecting the MFD to the internet via Wi-Fi access points or mobile hotspots.
Details how to connect a smart device to the MFD's Wi-Fi for internet access or web interface.
Provides possible causes and corrective actions for common marine electronics problems.
Details problems with power up or keeping the unit on, and their solutions.
Lists possible causes and solutions for problems with the radar scanner and screen.
Describes common GPS problems, their causes, and solutions for achieving a fix.
Details warnings from automatic route generation and actions to correct issues.
Lists possible causes and solutions for problems with the sonar image and depth readings.
Explains types of sonar crosstalk interference and methods for reducing it.
Addresses problems with thermal camera video display, controls, and image quality.
Covers problems with data sharing between connected equipment and network issues.
Details common Wi-Fi connection problems and solutions for mobile apps and signal issues.
Covers problems with Bluetooth connectivity, media player control, and signal issues.
Addresses touchscreen issues like touch lock, calibration, and saltwater deposits.
Provides contact information for Raymarine product support, warranty, and service.
To Next Page