EasyManua.ls Logo

Raymarine iTC-5 - User Manual

Raymarine iTC-5
50 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
© 2019 Raymarine UK Limited
87220-2Document number:
10-2019Date:
English (en-US)
Installation instructions
Wind Vane
Long & Short Arm

Table of Contents

Questions and Answers

  • S
    Steven LucasJul 25, 2025
    Why is instrument data unavailable on all Raymarine Media Converter displays?
    • A
      Ashley SmithJul 25, 2025
      If instrument, engine, or other system data is unavailable at all displays, it could be due to several reasons. First, check the data bus (e.g., SeaTalkng) wiring and its connections to ensure data is being received at the display and verify the overall integrity of the data bus wiring. Also, check the source of the missing data (e.g., ST70 instrument or engine interface) and the power to the SeaTalk bus to ensure it is operating correctly. If a software mismatch between equipment may prevent communication, contact Raymarine technical support.
  • B
    Brian MontoyaAug 2, 2025
    What to do if instrument data is missing from some Raymarine iTC-5 displays?
    • J
      Justin BestAug 2, 2025
      If instrument or other system data is missing from some but not all Raymarine Media Converter displays, it's likely a network issue. Ensure all required equipment is connected to the network and check the status of the Raymarine network Switch. Also, make sure that SeaTalkhs/ RayNet cables are free from damage. If a software mismatch between equipment may prevent communication, contact Raymarine technical support.
  • M
    mmooreAug 10, 2025
    Why does Raymarine Measuring Instruments show dashes on the display?
    • J
      Jessica BryanAug 10, 2025
      Dashes on the display might appear because the wind data is set to ‘True’ wind, but there's no speed through water (STW) data available. Alternatively, there could be a connection problem with the wind vane transducer. To resolve this, you can set the wind data to ‘Apparent’ and check if wind data appears. If it does, and you need ‘True’ wind, verify the source of STW data. Also, inspect the cabling for any damage, check the cable junction box (usually at the mast bottom) for damage and corrosion, ensuring connections are clean and secure, repairing or replacing as needed. Check connections to the display or converter and disconnect the wind vane arm and check arm and base connectors for damage and corrosion, ensuring they are clean and secure, repairing or replacing if necessary.
  • K
    Kevin GrantAug 17, 2025
    What to do if Raymarine Measuring Instruments data appears to be incorrect?
    • J
      jerry70Aug 17, 2025
      If the data appears incorrect, it may be because the wind vane hasn't been calibrated or has lost its calibration settings. You should re-calibrate the wind vane.

Summary

Important Information

Product Installation and Operation Warnings

Critical warnings for safe installation and operation.

Water Ingress Disclaimer

Explains waterproof rating and limitations.

General Disclaimer

Outlines Raymarine's responsibilities and limitations.

Declaration of Conformity

States compliance with relevant EU directives.

Warranty Registration

Instructions for registering the product for warranty benefits.

Product Disposal Guidelines

Information on environmentally responsible disposal of equipment.

Intended Use: IMO and SOLAS

Specifies applicability for leisure boats and workboats.

Technical Accuracy Disclaimer

Notes on information accuracy and product updates.

Document and Product Information

Product Documentation

Details relevant documentation available for the wind vane transducer.

Applicable Products

Identifies specific Raymarine wind vane transducer models covered.

Compatible Displays

Details instrument displays compatible with the wind vane transducer.

Compatible Converters and Pods

Explains connection options using converters and pods.

Parts Supplied - Transducers

Lists components included in transducer packaging.

Parts Supplied - Replacement Assemblies

Lists components included with replacement assemblies.

Installation Guide

Tools Required

Lists necessary tools for installing the wind vane transducer.

Selecting a Location

Guidance and requirements for choosing an optimal mounting location.

Mounting

Step-by-step instructions for physically mounting the wind vane unit.

Replacing an Existing Wind Vane

Details options and procedures for replacing older wind vane units.

Connections and Cabling

General Cabling Guidance

Best practices for cable types, routing, strain relief, and shielding.

Cable Routing

Specific instructions for routing cables through masts and decks.

Wind Vane Connections

Details how to make final electrical connections for the wind vane.

System Checks and Troubleshooting

Troubleshooting

Guide to diagnosing and resolving common installation/operation problems.

Wind Data Troubleshooting

Specific steps for wind data display issues.

Operation and Calibration

Calibration and Linearization

Importance of calibrating transducer for accurate readings.

Operation Instructions

Directs users to display documentation for detailed operation.

Maintenance and Cleaning

Wind Vane Routine Checks

Lists essential checks for wind vane functioning.

Unit Cleaning Instructions

Provides steps for cleaning the wind vane unit.

Technical Support and Resources

Raymarine Product Support and Servicing

Information on obtaining support, warranty, and repair services.

Learning Resources

Details available resources like video tutorials and training courses.

Technical Specifications

Physical Specification

Provides weight and dimensions for wind vane assemblies.

Conformance Specification

Lists compliance standards and certifications for the product.

Spares and Accessories

Wind Vane Spares and Accessories

Lists available spare parts and accessories for the wind vane.

Raymarine iTC-5 Specifications

General IconGeneral
BrandRaymarine
ModeliTC-5
CategoryMedia Converter
LanguageEnglish

Related product manuals