Applicable
products
This document is
applicable to the RV-2oo, RV-212(P/S),
and Rv-2zo(P/s) Realvision"
3D bronze thru-hull
transducers.
These transducers
are capable of
producing
3D
sonar
images
when connected to Realvision'.3D variant
MFDS running LightHouse'"
3 software. Five transducers are available in
the RV-2xx series,
each having the same external shape and
dimensions.
D'13799-1
splii-pair of RV-212(P/5)
or RV-220(P/S) transducers.
The
hull
geometry
of
your
vessel determines the most appropriate transducers
to use. You should fit transducers
whose internal elements are matched to within t6' of
your
hull's
Model no. Part no.
Descripiion
Hull
geometry
RV-200
A80465
Realvision'" 3D Bronze Thru-Hull Transducer,
0', single
("all
in one")
Hull with O'(flat-bottom) to 6' deadrise angle.
RV-212P 480466
Realvision'" 3D Bronze Thru-Hull
Transducer, 12', split-pair
Hull with 6'to 18' deadrise angle,
port
side
(pair
with A80467 below)
RV-212S
AAO467
Hull with
6" to'18' deadrise
anqle, starboard side
(pair
with 480466 above)
RV.22OP A80468
Realvision" 3D Bronze Thru-Hull Transducer, 2O',
split-pair Hull with 14'to 26" deadrise angle,
port
side
(pair
with A80469 below)
RV-220S A80469
Hull with
'14"
to
26"
deadrise angle,
starboard
side
(pair
with A8O468 above)
.
Bronze
thru-hull transducers
are
recommended for fiberglass
and wooden hulls and should
not
be used
on a
metal hull.
.
Do NOT install
bronze transducers on vessels with a
positive
ground
system.
refer to the separate installation
sheet.
Tools required
The
following tools are required to install any of the
transducers listed
under'Applicable
products".
6 75 mm
/ 3
inch wrench
(spanner)
or suitable
size adjustable wrench
(spanner)
7
Marine
grade
sealant
(non-acetate
based)
8 Adhesive tape
Warning: Transducer
operation
Only test and operate the transducer
in the
water. Do NOT operate out of
water as
overheating
may
occur.
II
Warning: Marine-grade
sealant
Only use marine-grade neutral
cure
polyurethane
sealants. Do NOT
use
sealants containing acetate or silicone,
which
can cause damage to
plastic pans.
Caution: Transducer cable
.
Do NOT use the transducer cable to
lift or suspend the transducer; always
support the transducer body dlrectly
during installation.
.
Do NOT
cut, shorten,
or
splice
the
transducer cable.
.
Do NOT remove the connector.
lf
the cable
is
cut, it cannot
be repaired.
Cutting the cable will also void the
warranty.
Testing the transducer
Transducer
operation should be checked before
installation.
1. Connect the
transducer to the
multifunction
display's
transducer connection.
2. Fully submerge the transducer in water.
3.
Power
up the display.
4. Open a Fishfinder
application
on
your
display.
5. lf required, select the relevant transducer/channel
from the Channel selection
page (Menurlicheiiilil).
6. Check that accurate
depth and
temperature
readings
are displayed.
7. lt
you
experience
difficulties
obtaining readings
then
contact Raymarine Technical Support.
Multiple transducers
Note: lf
you
are installing a
split-pair
of transducers
(for
example, an RV-212P unit with an RV-212S
unit),
ensure that
you
test both transducers together
by
connecting them to the
multifunction display using a
Y-cable and extension cable.
Refer to the colored
"Port"
and
"Starboard" labels on
the cables to
ensure that
you
connect the transducer
cables to the
correct Y-cable tails.
1
Power
drill
2
62
mm
/ 23/e inch hole cutter
Drill
bit
(suitable
size for drilling
pilot
holes)
4
9 mm
/
3/a
inch
drill bit
(for
drilling
anti-rotation
bolt hole)
5 Half round file
To Next Page
Need help?
General
