Razor GGC1643M - User Manual

Questions and Answers

K
Kathryn OrozcoAug 15, 2025
What to do if the Razor GGC1643M burner won't light using the igniter?
- K
  Kaitlin JohnsonAug 15, 2025
  If the burner of your Razor Griddle won't light using the igniter, several factors could be at play. First, ensure the LP gas tank valve is open and the regulator is securely attached. If the tank is low or empty, replace or refill it. Cooking residue on the wires or electrode can also be the culprit, so try cleaning them with rubbing alcohol. If the electrode and burners are wet, wipe them dry. For cracked/broken electrodes, loose/disconnected wires, shorting wires, or a bad igniter, replacement parts may be needed, so contact Customer Care.
C
Calvin JacobsAug 18, 2025
Why is the flame yellow or orange on my Razor GGC1643M?
- Z
  Zachary YoungAug 19, 2025
  If the flame on your Razor Griddle is yellow or orange, it could be due to a few reasons. If it's a new burner, residual manufacturing oils might be present; burn the griddle for 15 minutes on high with the lid closed. Spider webs or insect nests in the venturi can also cause this issue, so clean the venturi. Additionally, food residue or grease on the burners can affect the flame, so ensure they are clean. Finally, check the alignment of the valve to the burner/venturi tube to ensure they are properly engaged.
G
Gregg PierceAug 21, 2025
Why is there a sudden drop in gas flow or reduced flame height on my Razor GGC1643M Griddle?
- M
  Mary GrayAug 21, 2025
  A sudden drop in gas flow or reduced flame height in your Razor Griddle can occur if the LP gas tank is out of gas; in this case, exchange, refill, or replace the LP gas tank. Alternatively, the overfilling prevention device may have been activated. To address this: turn the control knobs to “ OFF”, wait 30 seconds, and light the griddle. If flames are still too low, reset the overfilling prevention device by turning the control knob(s) “ OFF”, turning the LP gas tank valve to “CLOSED”, disconnecting the regulator, turning control knobs to and (HIGH), waiting 1 minute, turning control knobs to “ OFF”, reconnecting the regulator and leak checking connections, and lighting the griddle.
V
Virginia JonesAug 25, 2025
What to do if the Razor Griddle burner will not light with a match?
- M
  Mia DeleonAug 26, 2025
  If the burner of your Razor Griddle won't light with a match, several issues could be the cause. First, check if the LP gas tank is empty and exchange, refill, or replace it if needed. If the tank isn't empty, there might be no gas flow, refer to “Sudden drop in gas flow or reduced flame height”. Ensure the coupling nut and regulator are fully connected by tightening the coupling nut by hand until a solid stop. Also, check for any obstruction of gas flow by clearing the burner/venturi tube and inspecting for bent or kinked hoses. Make sure the burner is properly engaged with the valve, and clean the burner/venturi tube to remove any spider webs or insect nests. Finally, clean any clogged or blocked burner ports.
J
Janet TorresAug 28, 2025
How to prevent flare-ups on my Razor GGC1643M?
- J
  John GentryAug 28, 2025
  Flare-ups on your Razor Griddle can be caused by grease buildup, so remove and clean all griddle parts. Excess fat in the meat can also contribute; trim fat from meat before cooking. High cooking temperatures may also be the cause, so adjust to a lower cooking temperature.
L
Laura CarlsonAug 30, 2025
Why does the flame go out on my Razor Griddle?
- W
  wlangAug 30, 2025
  If the flame on your Razor Griddle goes out, it could be due to high or gusting winds; avoid using the griddle in such conditions. It could also be due to low LP gas, so exchange, refill, or replace the LP gas tank. Alternatively, the overfilling prevention device may have been activated; refer to “Sudden drop in gas flow or reduced flame height”.
D
Diane CampbellSep 3, 2025
Why is there an irregular flame pattern on my Razor Griddle?
- A
  Abigail BlackSep 3, 2025
  An irregular flame pattern on your Razor Griddle, where the flame doesn't run the full length of the burner, is typically due to clogged or blocked burner ports. Cleaning the burner ports should resolve this issue.
H
huntjaclynSep 5, 2025
What to do about a persistent grease fire on my Razor Griddle?
- W
  walkerchristineSep 5, 2025
  A persistent grease fire on your Razor Griddle is likely due to grease trapped by food buildup around the burner system. To address this, turn the control knobs to “ OFF”, turn the LP gas tank valve to “CLOSED”, leave the lid in closed position and let the fire burn out. After the griddle cools, remove and clean all parts.
F
Frank BaileySep 8, 2025
What causes flashback (fire in burner tube(s)) in my Razor Griddle?
- A
  abraySep 8, 2025
  Flashback, or fire in the burner tubes of your Razor Griddle, indicates that the burners and/or burner/venturi tube are blocked. Cleaning these parts should resolve the issue.
A
amberevansSep 12, 2025
Why has my Razor Griddle started to rust?
- A
  Angela StevensSep 12, 2025
  With use the griddle surface will rust, this is normal. Follow the “Refurbish the Griddle Surface” instructions in the “Seasoning Griddle” section to season your griddle surface.

Summary

Parts and Hardware

Parts List

Comprehensive list of all griddle components and their identification numbers.

Expanded View Diagram

Visual diagram showing the assembled griddle with numbered parts.

Tools Required for Assembly

Details on included hardware (screws, nuts) and tools necessary for griddle assembly.

Transporting & Storage Instructions

Operating Instructions

Checking for Leaks

Essential safety procedure to identify and address gas leaks before operation.

Operating Main Burners

Step-by-step instructions for igniting and controlling the primary burners.

Lighting

Detailed steps for igniting the griddle's burners safely.

Turning Off

Procedure for safely shutting down the griddle after use.

Controlling Flare-ups

Guidance on managing and minimizing grease fires during cooking.

Operating Sear Burner

Instructions specific to using the high-temperature sear burner function.

Cleaning and Care

Cleaning Cart Surfaces

Methods for cleaning the exterior surfaces of the griddle cart.

Cleaning Main Burners

Detailed instructions for cleaning the internal burner components.

Before Storing

Steps to take for proper cleaning and preparation before storing the griddle.

Seasoning Griddle

Process for preparing and maintaining the griddle surface for optimal cooking.

Refurbish the Griddle Surface

Steps to restore a griddle surface that has lost its seasoning or developed rust.

Summary

Parts and Hardware

Parts List

Comprehensive list of all griddle components and their identification numbers.

Expanded View Diagram

Visual diagram showing the assembled griddle with numbered parts.

Tools Required for Assembly

Details on included hardware (screws, nuts) and tools necessary for griddle assembly.

Transporting & Storage Instructions

Operating Instructions

Checking for Leaks

Essential safety procedure to identify and address gas leaks before operation.

Operating Main Burners

Step-by-step instructions for igniting and controlling the primary burners.

Lighting

Detailed steps for igniting the griddle's burners safely.

Turning Off

Procedure for safely shutting down the griddle after use.

Controlling Flare-ups

Guidance on managing and minimizing grease fires during cooking.

Operating Sear Burner

Instructions specific to using the high-temperature sear burner function.

Cleaning and Care

Cleaning Cart Surfaces

Methods for cleaning the exterior surfaces of the griddle cart.

Cleaning Main Burners

Detailed instructions for cleaning the internal burner components.

Before Storing

Steps to take for proper cleaning and preparation before storing the griddle.

Seasoning Griddle

Process for preparing and maintaining the griddle surface for optimal cooking.

Refurbish the Griddle Surface

Steps to restore a griddle surface that has lost its seasoning or developed rust.

The device is an Outdoor LP Gas Griddle, Model No. GGC1643M, designed for residential outdoor cooking. It operates on liquid propane (LP) gas and features a griddle surface for cooking.

Function Description:

This outdoor griddle is designed for cooking food using LP gas burners. It includes a main griddle surface, side shelves for preparation or holding items, and a grease management system. The griddle is intended for outdoor use only and should not be operated in enclosed areas like buildings or garages. It is crucial to follow all safety warnings and instructions for proper assembly, operation, and maintenance to prevent injury, property damage, fire, or explosion.

Important Technical Specifications:

Fuel Type: Liquid Propane (LP) gas only. Conversion to natural gas is dangerous and will void the warranty.
LP Gas Cylinder: Requires a standard 20 lb (9 kg) LP gas cylinder with Acme Type 1 external threaded valve connection (not included). The cylinder must be constructed and marked in accordance with U.S. DOT or Canadian CSA standards, arranged for vapor withdrawal, and equipped with a listed overfilling prevention device (OPD) and a cylinder collar.
Inlet Pressure: Designed to operate at an inlet pressure of 11 inches water column.
Burners: Features multiple burners (one U burner and three standard burners, totaling four burners) with individual control knobs. There is also a dedicated sear control knob.
Ignition: Utilizes an igniter for lighting burners. A lighting hook is provided for manual lighting with a match if the igniter fails.
Clearance: Minimum clearance from sides and back of the unit to combustible construction is 36 inches (91.4 cm). It should not be used under any type of overhang or roof.
Side Shelf Weight Capacity: Maximum side shelf weight is 33 lbs (15 kg).
Assembly: Requires two people for assembly and takes approximately one hour.
Dimensions (LP Gas Tank): Approximately 17.9 inches (45.5 cm) in height and 12.2 inches (31 cm) in diameter for a 20 lb (9 kg) tank.

Usage Features:

Outdoor Use Only: Strictly for outdoor use, away from walls, structures, or buildings (minimum 10 feet / 3.05 m clearance). Not for commercial use.
Side Shelves: Foldable side shelves provide additional workspace. They must be securely held while opening and closing.
Grease Management: Includes a grease cup to collect cooking grease, which must be emptied and properly disposed of after each use.
Control Knobs: Individual control knobs for each burner allow for precise temperature adjustment, from OFF to HIGH.
Sear Burner: A dedicated sear burner operates at very high temperatures for searing food and sealing in juices.
Leak Testing: A leak test must be performed before each use and every time the LP cylinder is connected. A solution of liquid dish soap and water is used to check for bubbles at connections.
Lighting Procedure: Step-by-step instructions for lighting burners using the igniter or a match with the provided lighting hook.
Flare-up Control: Guidance on minimizing flare-ups by trimming excess fat, cooking high-fat meats on low settings, and ensuring proper grease drainage. In case of a grease fire, turn off control knobs and the LP gas tank valve; do NOT use water.
Seasoning Griddle: Critical for prolonging the griddle's life, making the cooking surface non-stick, and preventing rust. Seasoning is required before first use and after each use. This involves applying cooking oil and heating the griddle until the oil smokes, repeating the process multiple times.
Refurbishing Griddle Surface: Instructions are provided for restoring the griddle surface if it has rust or stubborn food residue, involving scrubbing with a BBQ stone and re-seasoning.

Maintenance Features:

Regular Cleaning: The griddle should be thoroughly cleaned and inspected on a regular basis. All cleaning and maintenance should be done when the griddle is cool and the fuel supply is disconnected.
Cart Surfaces: Clean with mild dish soap and water, or a citrus-based degreaser for stubborn stains.
Burner Cleaning: Requires two people to remove the griddle surface for access. Burners should be cleaned of residue, dirt, and clogged ports (using a stiff wire). Venturi tubes should be cleaned with a small bottle brush or compressed air. Burners should be inspected for damage and replaced if necessary.
Hose Inspection: The regulator and hose assembly should be inspected before each use for abrasion, wear, cuts, or leaks. Replace if damaged.
Storage: Before storing, the griddle must be cooled, cleaned, and seasoned. The LP gas tank must be disconnected and stored outdoors in a well-ventilated area, away from children and temperatures above 125°F. If storing the griddle indoors, the LP tank must be removed and stored outdoors. A griddle cover is recommended for outdoor storage.
No Abrasive Cleaners: Abrasive cleaners and oven cleaner should not be used on any part of the griddle.
No Valve Orifice Enlargement: Do not enlarge valve orifices or burner ports during cleaning.
Burner Flame Condition Check: A chart is provided to help identify if burners need cleaning based on flame appearance (soft blue flames with slight yellow tips are normal; noisy hard blue flames or wavy yellow flames indicate a need for cleaning or replacement).