4 5
AA
Need Help? Visit our website for replacement parts, product support, a list of authorized service centers in the US and customer service contact information
at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service
contact information is listed at the back of this manual.
1 Assemble the flag as shown.
1 Locate Adjustment Knob (A). Turn knob to the left to loosen and the pull knob up.
Slide and adjust the frame to the preferred length.
2 Turn Adjustment Knob (A) to the right to lock into place.
2 Insert flag into fixed hole located behind the seat.
Adjusting the Frame Length
Attaching the Flag
1
Remove the plastic packing material from the caster wheel.
Discard the plastic packing material.
2 Put the wheel screw into the frame tube and using a 5 mm
Allen wrench, tighten the bolt under the rear wheel caster.
Attaching the Rear Caster Wheels
Required Tool: 5 mm Allen Wrench (included)
WARNING: Failure to properly
tighten the bolts that affix the wheels
can cause you to lose control and crash.
Note: Practice riding only in wide open
areas clear from curbs, parking blocks
and other obstacles. Impacting the
wheels against any hard surface can
damage the wheels. Wheels are not
covered under your limited warranty.
PRE-RIDE CHECKLISTASSEMBLY AND SET-UP
Wheels
Periodically inspect the wheels for excess wear.
Frame, Fork and Drift Bars
Check for cracks or broken connections. Although broken frames are
rare, it is possible for an aggressive rider to run into a curb or object
and wreck and bend or break the frame. Get in the habit of inspecting
your product on a regular basis.
Hardware/Loose Parts
Check and secure all fasteners before every ride. Make sure the
bolts and casters are tight. There should not be any unusual rattles
or sounds from loose parts or broken components. If the unit is
damaged, do not ride. Reference “Safety Warnings”
on page 1 of this manual.
Safety Gear
Always wear proper protective gear, such as an approved safety helmet.
Elbow pads and kneepads are recommended. Always wear closed toe shoes
(lace-up with rubber soles) and keep shoelaces tied and out of the way of
the wheels. NEVER RIDE BAREFOOTED OR IN SANDALS.
Laws and Regulations
Always check and obey any local laws or regulations.
Be Careful!
This product is not for aggressive or trick riding. Avoid steep inclines and
don’t ride too fast — you can lose control and fall. Skateboard parks are not
designed for young riders. Never ride in traffic or on the street and watch
your surroundings for pedestrians, bikers, boarders and skaters.
Maintain a hold on the Drift Bars at all times.
How to Ride
The Crazy Cart Shuffle is designed for learning at a slow pace. While seated, grasp grips on the Drift Bars and place both feet on the
Foot Bar. Using feet, move the Foot Bar from side-to-side to propel the product. Using hands, move Drift Bars up and down to spin
and drift. Maintain a hold on the Drift Bars at all times.
WARNING: When riding, both feet
must be placed securely on Foot Bar.
WARNING: Do not allow hands, feet,
hair, body parts, clothing, or similar articles
to come in contact with the wheels or
other moving components.
With the Drift Bars down, move the
Foot Bar from side-to-side to propel the
product forward.
While turning in either direction, pull up the Drift Bars to initiate drifts and spins.
Use Foot Bar to control your rotation and direction of travel. Razor recommends that
you practice drifting and spinning in an open area free from obstructions before
riding your Crazy Cart Shuffle around others.
Push the right side of the Foot Bar with
your foot to turn left.
Push the left side of the Foot Bar with
your foot to turn right.
How to Move Forward How to Turn Left How to Turn Right
How to Drift and Spin
USAGE
To Next Page
Loading...
