RCm 33.BY.002 BYTE 461

Questions and Answers

C
crystalcollinsAug 5, 2025
Why won't my RCm 33.BY.002 BYTE 461 Blower switch on?
- I
  Ian MurphyAug 5, 2025
  The RCm Blower may not switch on due to several reasons: the battery charge might be low, so check the charge status and recharge if needed; the batteries might not be connected properly, so connect the batteries as shown in the battery connection diagram; the 230V AC cable might be disconnected (for AC-powered machines), so connect the cable to the electrical network; the 3A electronic control fuse might be blown, so check and replace it if necessary; or the start-up switch key might not be turned to position “1”, so turn the key to that position.
J
Jeff AndersonAug 9, 2025
What to do if my RCm 33.BY.002 BYTE 461 squeegee doesn't dry the floor completely?
- P
  parrishdeborahAug 9, 2025
  If the squeegee on your RCm Blower isn't drying the floor completely, there could be a few reasons. The squeegee drainage tube might be disconnected, so reconnect it. Also, the suction tube could be clogged, so dismantle and clean it. Debris might be caught in the squeegee, so remove any debris. There could be suction loss, so fix any leaks. The tube and suction motor gaskets located under the recovery tank might be damaged, so replace the gasket(s). Finally, the squeegee blades might be worn, so turn or replace the blades.
B
balvarezAug 13, 2025
Why is my RCm 33.BY.002 BYTE 461 Blower not cleaning well?
- A
  April PerezAug 13, 2025
  If your RCm Blower isn't cleaning well, it could be due to a worn brush, which should be replaced. The cleaning solution might be unsuitable, so replace it with a more appropriate one. The brush might not be suitable for the floor type, so use suitable brushes. Lastly, the work speed might be too high, so reduce it.
J
Jamie JohnsonAug 18, 2025
What to do if suction motor does not switch on in RCm 33.BY.002 BYTE 461 Blower?
- N
  nfisherAug 18, 2025
  If the suction motor on your RCm Blower does not switch on, first check if the batteries are connected and connect them if they are not. Next, inspect the suction motor carbon brushes for wear and replace them if necessary. Also, check if the suction motor is disconnected or damaged; check the connection or replace the motor if needed. Finally, see if the fuse is blown and replace it if it is.
L
Lucas McknightAug 22, 2025
Why does RCm Blower spray water in the joint space between tiles?
- J
  Jerry RamirezAug 22, 2025
  The squeegee has not been assembled and regulated correctly, so you need to properly assemble and regulate squeegee.
B
Brenda SanchezAug 27, 2025
What to do if cleaning solution doesn't come down on the brushes of RCm Blower?
- J
  Jessica BlakeAug 27, 2025
  If the cleaning solution isn't coming down or only a small amount is coming down on the brushes of your RCm Blower, the brush water hose may be clogged, so clean the tube. The electrovalve may be damaged or dirty, so clean and/or replace the electrovalve. The filter may be clogged or faulty, so clean or replace the filter.
D
dana54Aug 31, 2025
What to do if the brush does not rotate in RCm 33.BY.002 BYTE 461 Blower?
- L
  leecarolynAug 31, 2025
  If the brush does not rotate in your RCm Blower, ensure the batteries are connected. If not, connect them. Also, check the motor carbon brushes for wear and replace them if necessary. Finally, inspect the motor for disconnections or damage; check the connection or replace the motor if needed.