OVERCRANK
WARNING LED
1
2
3
4
5
6
7
8
9
10
11
12
(11966)
OVERCRANK PROTECTION CONTROLLER
BYPASS KEY
SWITCH
(CONNECT TO
+VE PROTECTED
IGNITION SUPPLY)
START SIGNAL
OUTPUT
(ENGINE CRANK)
AT IGNITION
KEY SWITCH
STARTER
MOTOR SLAVE
SOLENOID(S)
GROUND
+VE
PROTECTED
IGNITION
SUPPLY
(BLUE)
8586
30 87
!
www.rct.net.auN12596
OVERCRANK PROTECTION
CONTROLLER
11966
RD-4
BK-4
YL/BU-4
OR-4
YL-FVT
PU-FVT
BK/WH-3
REF NOTE
GN-FVT
WH-FVT
PK-FVT
BU-FVT
RD/WH-3
NOTE:
WHEN USING LED PART NO 11111, OR AN EQUIVALENT NO LOAD LED, A
RESISTOR SHOULD BE CONNECTED ACROSS THE LED TO PREVENT
CURRENT LEAKAGE WHICH CAUSES A FALSE INDICATION. RESISTOR TYPE
IS (1W 1.2K OHM RCT PART NUMBER 11981)
WARNING! A RELAY IS REQUIRED IN THIS SYSTEM AS A FAIL TO SAFE
CIRCUIT. FAILURE TO INCLUDE A RELAY IN THE CIRCUIT MAY RESULT IN
DAMAGE TO THE ENGINE AND OR COMPONENTS.
1 2 3 4 5 6 7 8 9 10 11 12
B
A
C
D
E
F
G
H
B
A
C
D
E
F
G
H
1 2
3
4
5 6
7
8 9 10
11 12
A4
COPYRIGHT - ALL RIGHTS RESERVED
This drawing is the property of REMOTE
CONTROL TECHNOLOGIES PTY LTD (RCT),
and is not to be copied or used in whole or in
part for any purpose without the express
authority of RCT. The drawing is to be returned
to RCT, on demand.
OVERCRANK
PROTECTION
CONTROLLER
EXTERNAL WIRING
www.rct.net.au
UNCONTROLLED DOCUMENT
REV
5
DWG No
501d
STATUS
NTS
SCALE
Released
SHEET
1 of 1
BY
RD
DRN
CW
DATE
05/02/14
APPD
DW
DATE
05/02/14
STOCK
CODE
MH-MV-OCC
PART
NO
11966
3rd ANGLE
PROJECTION
ALL DIMENSIONS IN MILLIMETERS
WIRE LEGEND
BK - BLACK PK - PINK
BU - BLUE PU - PURPLE
BN - BROWN RD - RED
GN - GREEN WH - WHITE
GY - GREY YL - YELLOW
OR - ORANGE TQ - TURQUOISE
REV ZONE DESCRIPTION BY DATE
1
LED wire changed from
pin 9 to 10, key start wire
changed from pin 5 to 8,
bypass key, key switch
and protected battery
supply descriptions
amended
DW 25/03/14
2
CHANGE TO RELAY
AND BATTERY SUPPLY
TEXT. OPERATION
REWRITTEN, TITLE
CHANGE
RD 26/03/14
3
D7
bypass switch changed to
N/O
DAS 05/12/14
4
C3, E3,
B5-E6
text added to label and
below controller, wire
colours added, earth
changed for LED
CamB 02/11/15
5
H1-3,
E1-3,
F7, F11
Wiring Connections table
added, Warning note
added, Pin 1 and 6 label
changed
MT 06/05/16
WIRING CONNECTIONS
PIN WIRE FUNCTION
1
RD 12/24V IGNITION SUPPLY
2
BK GROUND
3
YL/BU ENGINE START/CRANK CONTROL OUTPUT
4 GN NOT USED
5
WH NOT USED
6
OR BYPASS KEY INPUT
7 PK NOT USED
8
YL ENGINE START/CRANK SIGNAL INPUT
9 BU
NOT USED
10 PU
POSITIVE OUT PUT TO LED
11 BK/WH GROUND FOR LED
12 RH/WH NOT USED
To Next Page
