34 LP1109
SCROLLING HELP TEXT IN DISPLAY LINE 3
[01] Set correct password [19] Select OFF function - relay is permanently off
[02] Enter advanced setup menu? Select POWER function - relay indicates power status OK
[03] Select temperature input Select ERROR function - relay indicates sensor error only
Select potentiometer input Select SETPOINT function - relay controlled by 1 setpoint
Select linear resistance input [20] Select Normally Closed contact
Select current input Select Normally Open contact
Select voltage input [21] Set relay setpoint
[04] Select 0.0-1 V input range [22] Activate relay on decreasing signal
Select 0.2-1 V input range Activate relay on increasing signal
Select 0-5 V input range [23] Set relay hysteresis
Select 1-5 V input range [24] No error action - undefined status at error
Select 0-10 V input range Open relay contact at error
Select 2-10 V input range Close relay contact at error
[05] Select 0-20 mA input range Hold relay status at error
Select 0-20 mA input range [25] Set relay ON delay in seconds
[06] Select 2-wire sensor connection [26] Set relay OFF delay in seconds
Select 3-wire sensor connection [27] Relay contact is Closed Inside Window
Select 4-wire sensor connection Relay contact is Open Inside Window
[07] Set resistance value low [28] Set relay window setpoint high
[08] Set resistance value high [29] Set relay window setpoint low
[09] Select Celsius as temperature unit [30] Set relay window hysteresis
Select Fahrenheit as temperature unit [31] No error action - undefined status at error
[10] Select TC sensor type Open relay contact at error
Select Ni sensor type Close relay contact at error
Select Pt sensor type Hold relay status at error
Select Cu sensor type [32] Set relay ON delay in seconds
[11] Select display unit [33] Set relay OFF delay in seconds
[12] Select decimal point position [34] Open relay contact at error
[13] Set display range low Close relay contact at error
[14] Set display range high [36] Select current as analogue output type
[16] Select Pt10 as sensor type Select voltage as analogue output type
Select Pt20 as sensor type [37] Select 0-20 mA output range
Select Pt50 as sensor type Select 4-20 mA output range
Select Pt100 as sensor type Select S4-20 mA with safety readback
Select Pt200 as sensor type Select 20-0 mA output range
Select Pt250 as sensor type Select 20-4 mA output range
Select Pt300 as sensor type Select S20-4 mA with safety readback
Select Pt400 as sensor type [38] Select no error action - output undefined at error
Select Pt500 as sensor type Select downscale at error
Select Pt1000 as sensor type Select NAMUR NE43 downscale at error
[17] Select Ni50 as sensor type Select NAMUR NE43 upscale at error
Select Ni100 as sensor type [39] Select 0.0-1 V output range
Select Ni120 as sensor type Select 0.2-1 V output range
Select Ni1000 as sensor type Select 0-5 V output range
[18] Select TC-B as sensor type Select 1-5 V output range
Select TC-E as sensor type Select 0-10 V output range
Select TC-J as sensor type Select 2-10 V output range
Select TC-K as sensor type Select 1-0.0 V output range
Select TC-L as sensor type Select 1-0.2 V output range
Select TC-N as sensor type Select 5-0 V output range
Select TC-R as sensor type Select 5-1 V output range
Select TC-S as sensor type Select 10-0 V output range
Select TC-T as sensor type Select 10-2 V output range
Select TC-U as sensor type [41] Set temperature for analogue output low
Select TC-W3 as sensor type [42] Set temperature for analogue output high
Select TC-W5 as sensor type
Select TC-Lr as sensor type
To Next Page
Loading...