RedMax GZ3500T - User Manual

Other manuals for RedMax GZ3500T

Workshop Manual56 pages

Owner's/Operator's Manual18 pages

Questions and Answers

Y
ythomasSep 3, 2025
What causes the carburettor to leak fuel in my RedMax GZ3500T Chainsaw?
- E
  Emily RaySep 3, 2025
  If the carburettor is leaking fuel in your RedMax Chainsaw, you can try the following: Tighten or replace the loose or defective fuel hose. Replace the membrane with a hole, or replace the worn needle/needle tip. Fix the binding control system, adjust the control system if it's set too high, or fix the leaking control system (air or fuel). You can also try tightening the cover on the carburettor pump side.
L
lori82Sep 1, 2025
How to fix irregular idling on my RedMax GZ3500T Chainsaw?
- B
  Brandon MartinSep 2, 2025
  To fix irregular idling on your RedMax Chainsaw, you can try the following: Replace the clogged fuel filter or fuel hose. Fix the leaking inlet hose (rubber). Tighten the loose clamping screws on the carburettor. Replace the worn throttle valve shaft, tighten the loose throttle valve screw, or replace the worn throttle valve. You can also fix the binding control system, the leaking control system (air or fuel), replace the worn center knob of the control system, replace the membrane with a hole, fix the leaking diaphragm/cover plate, or fix the crankcase leak.
W
William LeeAug 31, 2025
What to do if the engine of my RedMax Chainsaw stops when releasing the throttle?
- E
  Erica ReyesAug 31, 2025
  If the engine of your RedMax Chainsaw stops when releasing the throttle, try the following: Adjust the L-screw and H-screw. Replace the faulty pump diaphragm. Adjust the control system if it is set too high. Fix the binding control system. Replace the faulty diffuser jet.
L
Larry FisherAug 29, 2025
Why does my RedMax GZ3500T Chainsaw have low power?
- R
  Rebecca YorkAug 29, 2025
  If your RedMax Chainsaw is low on power, consider the following: * Adjust the H-screw. * Fix the clogged tank venting. * Replace the clogged fuel filter. * Address any impulse channel leaks or blockages. * Tighten the cover on the carburettor pump side and replace the faulty pump diaphragm if needed. * Fix the blocked air filter. * Address issues with the control system by fixing any binding, leaks (air or fuel), incorrect assembly, loose diaphragm rivet, hole in the membrane, or leaks in the control membrane/cover plate.
R
russellnicholsAug 27, 2025
Why my RedMax Chainsaw does not run at full throttle?
- D
  David WilsonAug 28, 2025
  If your RedMax Chainsaw won't run at full throttle, consider these potential solutions: Adjust the H-screw. Address any blockages by fixing the blocked air filter, clogged tank venting, clogged fuel filter, or clogged fuel hose. Replace any loose or defective fuel hoses. Address issues with the impulse channel by fixing any leaks or blockages. Ensure the cover on the carburettor pump side is tightened and replace the faulty pump diaphragm if necessary. Address air leaks by fixing the leaking inlet hose and tightening any loose clamping screws on the carburettor. Check the control system, adjusting it if set too low, ensuring it's not damaged, incorrectly assembled or binding. Also, fix any leaks in the control membrane or cover plate, or fix the clogged muffler.
L
Lauren AyersAug 26, 2025
What to do if my RedMax GZ3500T Chainsaw does not accelerate?
- S
  Seth PearsonAug 26, 2025
  If your RedMax Chainsaw does not accelerate, try these solutions: Adjust the L-screw and H-screw. Address any blockages by fixing the blocked air filter, clogged tank venting, clogged fuel filter, or clogged fuel hose. Replace any loose or defective fuel hoses. Also, fix the blocked impulse channel. Ensure the cover on the carburettor pump side is tightened and replace the faulty pump diaphragm if necessary. Address air leaks by fixing the leaking inlet hose and tightening any loose clamping screws on the carburettor. Check the control system, adjusting it if set too low, and ensuring it's correctly assembled and not binding. Replace the faulty diffuser jet, or fix the clogged muffler.
A
Angela GreenAug 25, 2025
How to fix ignition with no spark in my RedMax GZ3500T Chainsaw?
- N
  Nicole CoffeyAug 25, 2025
  If your RedMax Chainsaw has ignition problems with no spark, start by checking the spark plug. Make sure it is dry and clean. Also, ensure that the electrode gap is correct. Tighten the spark plug if it is loose. If the engine is flooded due to repeated starts with full choke, remove and clean the spark plug, put the product on its side with the spark plug hole away from you, pull the starter rope handle 6-8 times, assemble the spark plug and start the product.
J
Jennifer JohnsonAug 22, 2025
Why won't my RedMax GZ3500T engine start?
- A
  Anna Harris DDSAug 23, 2025
  If your RedMax Chainsaw engine won't start, there are a few potential causes. The starter pawls might be blocked, in which case you should adjust or replace them. Ensure you are using the correct fuel type; if not, drain the tank and refill it. If the fuel tank has been filled with chain oil, drain the fuel tank if you haven't tried starting the chainsaw.