EasyManua.ls Logo

Redring Expressions 500S - User Manual

Redring Expressions 500S
13 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
IMPORTANT:
This booklet should be left with the user after
installation and demonstration
REDRING EXPRESSIONS 500S
SMART TECHNOLOGY
ELECTRIC SHOWER
Installation and User Guide

Table of Contents

Questions and Answers

  • B
    blackwendyAug 17, 2025
    Why does my Redring Plumbing Product shower cycle from hot to cold?
    • J
      Justin MarshallAug 17, 2025
      If your Redring Plumbing Product shower cycles from hot to cold, it might be due to the shower temperature being set too high, which activates the thermal cut-out safety feature. To resolve this, turn knob “C” clockwise to increase water flow. Then, slowly increase the water temperature by turning knob “C” anti-clockwise until you reach a comfortable temperature. Remember to wait about 20 seconds after each adjustment to see its effect. You may also need to select the 'Med (medium)' setting.
  • D
    Dustin WoodAug 19, 2025
    How to fix too hot water from Redring Plumbing Product?
    • S
      Sara KellyAug 19, 2025
      If the water from your Redring Plumbing Product is too hot, try increasing the water flow by adjusting knob “C” clockwise. Selecting the 'Med (medium)' setting might also help. Additionally, ensure that the water supply pressure is sufficient by fully opening the service valve or stop cock. Check that the hose isn't kinked, which could restrict water flow, and clean the shower handset.
  • L
    Laura Barnes PhDAug 22, 2025
    What to do if Redring Plumbing Product water is too cold?
    • C
      Cynthia CookAug 22, 2025
      If the water from your Redring Plumbing Product is too cold, first, check that the power is on by verifying that the neon light is illuminated. Then, decrease the water flow by adjusting Knob “C” anti-clockwise. You might also need to select the 'High' setting. Another option is to select either the inner or outer only handset spray pattern.
  • C
    Charles RobinsonAug 25, 2025
    Why does Redring Plumbing Product water go cold during shower?
    • L
      Logan AdamsAug 26, 2025
      If the water from your Redring Plumbing Product goes cold while you're showering, first, check that the neon light is on. Also, make sure that the water pressure hasn't dropped significantly, which could cause the pressure switch to cut out—for example, if another tap is drawing water. Try raising the position of the shower handset as well.
  • B
    Billy KeithAug 27, 2025
    How to improve Redring Plumbing Product spray pattern?
    • C
      crawfordgaryAug 27, 2025
      If your Redring Plumbing Product spray pattern is poor, try cleaning the shower handset.
  • D
    Dale YoungAug 30, 2025
    Why does Redring Plumbing Product take longer to heat up?
    • J
      Jennifer FlemingAug 30, 2025
      If the water takes longer to heat up in your Redring Plumbing Product and the 'Overheat' light is on, it indicates that the thermal cut-out has activated after previous use. In this case, selecting the 'High' setting may be necessary.
  • R
    Robert AtkinsonSep 2, 2025
    How to troubleshoot cold water issue in Redring Plumbing Product?
    • B
      Brenda HinesSep 2, 2025
      If the water from your Redring Plumbing Product is too cold, check the circuit through the thermal cut-out, the microswitches on the pressure switch, and each element circuit. Also, check the operation of the relay and the tightness of the electrical connections.
  • J
    Jacob FrankSep 5, 2025
    What to do for water leak from Redring Plumbing Product pressure relief valve?
    • L
      lhowellSep 5, 2025
      If water leaks from the burst pressure relief valve of your Redring Plumbing Product, identify and eliminate the cause of high pressure. This could be due to a blockage on the outlet, such as a blocked shower handset. You may need to replace the pressure relief disc, noting that this is not covered by the guarantee.
  • B
    burchaustinSep 8, 2025
    How to clean Redring Plumbing Product solenoid valve filter?
    • A
      Ashley BarberSep 8, 2025
      If the water from your Redring Plumbing Product is too hot and the water flow is restricted by a blockage in the filter of the solenoid valve, switch off the water supply. Then, loosen the inlet connection to the solenoid. Use long-nosed pliers to remove the filter in the solenoid and flush it clean.
  • V
    vegamoniqueSep 10, 2025
    How to fix Redring Plumbing Product water flow control?
    • M
      Matthew AdamsSep 12, 2025
      If there is no control over the water flow in your Redring Plumbing Product, check that the Numbered Dial is correctly engaged into the Control Knob. Also, undo the headworks of the stabiliser valve to check that the stabiliser is in place and remove any debris in the valve.

Summary

INTRODUCTION

IMPORTANT SAFETY INFORMATION

HOW TO USE YOUR EXPRESSIONS 500 S SHOWER (DETAILED)

IF WATER IS TOO COLD

Adjusting temperature when water is too cold using knob C.

IF WATER IS TOO HOT

Adjusting temperature when water is too hot using knob C or power setting.

HOW YOUR EXPRESSIONS 500 S SHOWER WORKS

Effect of Seasonal Incoming Water Temperature Changes

Explains how seasonal temperature variations affect shower performance.

Effect of Other Water Devices on Incoming Water Supply

Explains how water pressure fluctuations impact shower temperature.

HOW TO MAINTAIN YOUR EXPRESSIONS 500 S SHOWER

WHAT TO DO IF THINGS GO WRONG (1)

WHAT TO DO IF THINGS GO WRONG (2)

PROFESSIONAL SERVICE

Checklist for qualified service personnel to diagnose issues.

REDRING AFTER SALES SERVICE

HOW TO INSTALL YOUR EXPRESSIONS 500 S SHOWER

FIXING THE SHOWER TO THE WALL

Instructions for mounting the shower unit and riser rail to the wall.

PLUMBING

ELECTRICAL

DEMONSTRATE OPERATION TO USER

ADDITIONAL ACCESSORIES

SPARE PARTS

GUARANTEE AND CONTACT DETAILS

GUARANTEE

Details warranty terms, conditions, and exclusions for the product.

EXCLUSIONS

Lists conditions and situations not covered by the product guarantee.

HOW TO USE YOUR EXPRESSIONS 500 S SHOWER (SUMMARY)

Notes

Provides helpful notes and tips for optimal shower operation and stabilization.

IMPORTANT WARNINGS!

Redring Expressions 500S Specifications

General IconGeneral
Energy Efficiency ClassA
Water Connection15mm
ApprovalsBEAB, CE
InstallationProfessional installation recommended
FeaturesOver temperature protection

Related product manuals