EasyManua.ls Logo

Remington RM1415A - User Manual

Remington RM1415A
60 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
®
IMPORTANT: Read and understand this manual before assembling or op-
erating this chain saw. Improper use of saw can cause severe injury. Keep
this manual for future reference.
MODELS
RM1215U, RM1415U, RM1415A
ELECTRIC CHAIN SAW
OWNER’S MANUAL
PART NO. 769-05149 P00 (06/09)

Table of Contents

Questions and Answers

  • B
    Bradley OrtegaAug 3, 2025
    What to do if my Remington RM1415A Chainsaw motor doesn't run when squeezing the trigger?
    • D
      dandersonAug 3, 2025
      If your Remington chainsaw motor doesn't run when you squeeze the trigger, there are several potential causes: 1. Ensure the switch lockout is fully pushed forward to release the trigger. 2. Check the extension cord connections to make sure they are secure. 3. Inspect the line fuse or circuit breaker. 4. Worn out motor brushes may be the reason. Please, see authorized service center. 5. There may be an open wiring circuit on the saw. Please, see authorized service center.
  • L
    Lonnie SmithAug 8, 2025
    Why is my Remington RM1415A Chainsaw chain not getting oil?
    • J
      Jordan MyersAug 8, 2025
      If your Remington chainsaw chain isn't getting oil, here's what to check: 1. The oil slot in the guide bar might be clogged. Remove the guide bar and clean the oil slot. 2. The oil might be too thick. Use the correct weight of oil. See Filling Oil Tank.
  • J
    Jasmin FryAug 12, 2025
    What to do if my Remington Chainsaw motor runs, but the chain does not move?
    • B
      bradleyamandaAug 12, 2025
      If your Remington chainsaw runs, but the chain doesn't move, remove and inspect the gear sprocket for damage.
  • J
    James BautistaAug 16, 2025
    Why does the chain keep coming off my Remington RM1415A Chainsaw?
    • T
      Tyler WilliamsAug 16, 2025
      If the chain of your Remington chainsaw keeps coming off the guide bar: 1. The chain is likely too loose. Tighten the chain. See Saw Chain Tension Adjustment. 2. The guide bar and chain might not be assembled correctly. See Assembly.
  • M
    Mr. Christopher ReedAug 20, 2025
    Why does my Remington Chainsaw run slow and stall easily?
    • V
      Valerie OsborneAug 21, 2025
      If your Remington chainsaw runs slowly or stalls easily, it could be due to low power supply voltage. The extension cord wire size might be too small. See Extension Cords.
  • T
    Tammy RamirezAug 25, 2025
    Why is my Remington RM1415A Chainsaw leaking oil?
    • D
      Daniel MartinezAug 26, 2025
      If your Remington chainsaw is leaking oil, tighten the oil cap. It is normal for oil to seep when the saw is not in use. Empty the oil tank when not in use.
  • J
    James GomezAug 29, 2025
    What to do if my Remington RM1415A Chainsaw produces sawdust instead of cutting?
    • M
      Mrs. Janet Arnold MDAug 30, 2025
      If your Remington chainsaw is producing only sawdust and not cutting unless heavily forced, the chain is likely dull. See Sharpening Saw Chain.

Summary

Safety and Warnings

Pre-Operation Safety Checks

Essential safety precautions and checks to perform before starting the chain saw.

Safe Operation Practices

Guidelines and warnings for safe operation of the chain saw during use.

Kickback Hazard and Prevention

Understanding kickback risks and the safety devices that reduce them.

Maintenance for Kickback Safety

How proper maintenance and chain care reduces kickback risk.

Unpacking and Product Identification

Unpacking and Initial Inspection

Steps for safely removing the product from its packaging and checking for damage.

Product Identification Features

Locating and understanding the key identification labels on the saw.

Chainsaw Component Glossary

Definitions of the various parts and cutting processes of the chain saw.

Assembly and Chain Tension

Chain Saw Assembly Guide

Step-by-step guide for assembling the chain saw components correctly.

Saw Chain Tension Adjustment

Instructions on how to properly adjust and maintain saw chain tension.

Chain Saw Operation

Oil System Management

Procedures for filling the oil tank and ensuring proper chain lubrication.

Extension Cord Safety

Selecting and using appropriate extension cords for safe operation.

General Cutting Techniques

Safe techniques for starting cuts and operating the saw for various tasks.

Tree Cutting Procedures

Detailed guidance on felling, limbing, bucking, and pruning trees.

Cleaning and Maintenance

Saw Body Cleaning

Methods for cleaning the exterior of the chain saw safely.

Guide Bar Maintenance

How to maintain the guide bar for optimal performance and safety.

Chain Sharpening Process

Step-by-step instructions for sharpening the chain cutters and depth gauges.

Storage, Parts, and Service

Replacing the Saw Chain

When and how to replace the saw chain for continued performance.

Long-Term Storage Guidelines

Proper procedures for storing the chain saw for extended periods.

Ordering Replacement Parts

Information on obtaining genuine replacement parts and approved accessories.

Authorized Repair Service

How to obtain authorized service for the chain saw.

Troubleshooting and Warranty

Troubleshooting Common Issues

Diagnosing and resolving common problems encountered with the chain saw.

Manufacturers Warranty

Details of the manufacturer's limited warranty, coverage, and service.

Remington RM1415A Specifications

General IconGeneral
BrandRemington
ModelRM1415A
CategoryChainsaw
LanguageEnglish

Related product manuals