EasyManua.ls Logo

Remington RM1632A - User Manual

Remington RM1632A
20 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
®
ELECTRIC CHAI SAW
OWNER'S MANUAL
MODELS: RM1632A, RM1635W
iMPORTANT: Read and understand this manual before assem=
bling or operating this chain saw. improper use of saw can cause
severe injury. Keep this manual for future reference.
PART NO. 769-05147 P00 (07/09)

Table of Contents

Questions and Answers

  • B
    Benjamin BallardAug 19, 2025
    What to do if my Remington RM1632A motor doesn't run when I squeeze the trigger?
    • J
      Jacob LeeAug 19, 2025
      If the motor of your Remington chainsaw does not run when you squeeze the trigger: 1. Ensure the switch lockout is pushed forward to release the trigger. 2. Check the extension cord connections to make sure they are not loose. 3. Check the line fuse or circuit breaker. 4. Contact an authorized service center to check worn out motor brushes. 5. Contact an authorized service center to check for an open wiring circuit on the saw.
  • J
    Jonathan NortonAug 21, 2025
    Why is my Remington RM1632A Chainsaw chain not getting oil?
    • B
      brian22Aug 21, 2025
      If your Remington chainsaw chain is not getting oil: 1. Remove the guide bar and clean the oil slot, as it may be clogged. 2. Use the correct weight of oil, as the current oil may be too thick. Check the manual section about Filling Oil Tank. 3. Remove the cap and clean the vent hole, as the vent in the oil cap may be clogged. 4. Remove the filter in the oil reservoir and clean it, as it may be clogged. 5. The pump may be damaged, in this case do not use the saw and contact an authorized service center.
  • G
    george48Aug 23, 2025
    Why does my Remington RM1632A run slow and stall easily?
    • S
      Stephanie LewisAug 23, 2025
      Your Remington chainsaw might run slowly and stall easily due to low power supply voltage. Check that the extension cord wire size is adequate. See Extension Cords section.
  • S
    stacy36Aug 26, 2025
    What to do if the chain comes off the guide bar on my Remington Chainsaw?
    • S
      Sara Hudson DVMAug 26, 2025
      If the chain comes off the guide bar on your Remington chainsaw: 1. Tighten the chain. See Saw Chain Tension Adjustment section. 2. Check that the guide bar and chain are assembled correctly. See Assembly section.
  • B
    Brittany RayAug 28, 2025
    Why Remington RM1632A produces only sawdust?
    • D
      Daniel SotoAug 28, 2025
      If your Remington chainsaw only produces sawdust and requires heavy forcing to cut, the chain is likely dull. See Sharpening Saw Chain section.
  • D
    diaztroyAug 30, 2025
    What to do if the motor of my Remington Chainsaw runs, but the chain does not move?
    • B
      Brandi SullivanAug 30, 2025
      If the motor of your Remington chainsaw runs but the chain does not move, remove and inspect the gear sprocket for damage.
  • W
    wilsonalexanderSep 1, 2025
    Why is my Remington RM1632A Chainsaw leaking oil?
    • M
      Molly ColemanSep 1, 2025
      It is normal for oil to seep from your Remington chainsaw when it is not in use. To minimize this, tighten the oil cap and empty the oil tank when the saw is not in use.
  • C
    cassandravillaSep 3, 2025
    Why is my Remington RM1632A Chainsaw smoking?
    • K
      Kathy DavisSep 3, 2025
      If your Remington chainsaw is smoking, the saw may be damaged. Do not use the saw and contact an authorized service center.
  • T
    Theresa JacksonSep 5, 2025
    What to do if my Remington Saw motor does not run when I squeeze the trigger?
    • L
      Lisa TurnerSep 5, 2025
      If the motor of your saw does not run when you squeeze the trigger, consider the following: 1. Ensure the switch lockout is pushed forward to release the trigger. 2. Check the extension cord connections to ensure they are not loose. 3. Inspect the line fuse or circuit breaker.
  • N
    Natalie GonzalesSep 7, 2025
    Why is my Remington Saw leaking oil?
    • J
      Jason RandolphSep 7, 2025
      It is normal for oil to seep when the saw is not in use. To mitigate this, tighten the oil cap and empty the oil tank when the saw is not in use.

Remington RM1632A Specifications

General IconGeneral
Bar Length16 inches
Motor Power12 amp
Weight10.8 lbs
Automatic OilingYes
Chain Pitch3/8 inch
Chain Gauge0.050 inches

Related product manuals