EasyManua.ls Logo

Remington RM1635W - User Manual

Remington RM1635W
20 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
®
ELECTRIC CHAI SAW
OWNER'S MANUAL
MODELS: RM1632A, RM1635W
iMPORTANT: Read and understand this manual before assem=
bling or operating this chain saw. improper use of saw can cause
severe injury. Keep this manual for future reference.
PART NO. 769-05147 P00 (07/09)

Table of Contents

Questions and Answers

  • K
    krichardsonAug 19, 2025
    What to do if my Remington RM1635W Chainsaw motor doesn't run when I squeeze the trigger?
    • K
      Kevin KerrAug 19, 2025
      If the motor of your Remington chainsaw does not run when you squeeze the trigger: 1. Ensure the switch lockout is pushed forward to release the trigger. 2. Check the extension cord connections to make sure they are not loose. 3. Check the line fuse or circuit breaker. 4. Contact an authorized service center to check worn out motor brushes. 5. Contact an authorized service center to check for an open wiring circuit on the saw.
  • S
    Samantha JenningsAug 21, 2025
    Why is my Remington RM1635W Chainsaw chain not getting oil?
    • S
      Shawn BurkeAug 21, 2025
      If your Remington chainsaw chain is not getting oil: 1. Remove the guide bar and clean the oil slot, as it may be clogged. 2. Use the correct weight of oil, as the current oil may be too thick. Check the manual section about Filling Oil Tank. 3. Remove the cap and clean the vent hole, as the vent in the oil cap may be clogged. 4. Remove the filter in the oil reservoir and clean it, as it may be clogged. 5. The pump may be damaged, in this case do not use the saw and contact an authorized service center.
  • B
    Brittany WeaverAug 23, 2025
    Why does my Remington RM1635W run slow and stall easily?
    • M
      Megan BallAug 23, 2025
      Your Remington chainsaw might run slowly and stall easily due to low power supply voltage. Check that the extension cord wire size is adequate. See Extension Cords section.
  • E
    Evan DunnAug 26, 2025
    What to do if the chain comes off the guide bar on my Remington RM1635W Chainsaw?
    • Z
      Zoe ThompsonAug 26, 2025
      If the chain comes off the guide bar on your Remington chainsaw: 1. Tighten the chain. See Saw Chain Tension Adjustment section. 2. Check that the guide bar and chain are assembled correctly. See Assembly section.
  • P
    pandersonAug 28, 2025
    Why Remington Chainsaw produces only sawdust?
    • S
      smithandreaAug 28, 2025
      If your Remington chainsaw only produces sawdust and requires heavy forcing to cut, the chain is likely dull. See Sharpening Saw Chain section.
  • J
    Jason EricksonAug 30, 2025
    What to do if the motor of my Remington RM1635W runs, but the chain does not move?
    • B
      Brett StewartAug 30, 2025
      If the motor of your Remington chainsaw runs but the chain does not move, remove and inspect the gear sprocket for damage.
  • N
    Nicholas BrownSep 1, 2025
    Why is my Remington RM1635W Chainsaw leaking oil?
    • K
      kevin56Sep 1, 2025
      It is normal for oil to seep from your Remington chainsaw when it is not in use. To minimize this, tighten the oil cap and empty the oil tank when the saw is not in use.
  • J
    jcoxSep 3, 2025
    Why is my Remington Chainsaw smoking?
    • C
      cynthia48Sep 3, 2025
      If your Remington chainsaw is smoking, the saw may be damaged. Do not use the saw and contact an authorized service center.
  • O
    olsenannSep 5, 2025
    What to do if my Remington Saw motor does not run when I squeeze the trigger?
    • B
      Bruce DavisSep 5, 2025
      If the motor of your saw does not run when you squeeze the trigger, consider the following: 1. Ensure the switch lockout is pushed forward to release the trigger. 2. Check the extension cord connections to ensure they are not loose. 3. Inspect the line fuse or circuit breaker.
  • T
    Thomas SmithSep 7, 2025
    Why is my Remington Saw leaking oil?
    • S
      Stacey KingSep 8, 2025
      It is normal for oil to seep when the saw is not in use. To mitigate this, tighten the oil cap and empty the oil tank when the saw is not in use.

Summary

Important Safety Information

Before Operating Saw

Basic safety precautions and checks before using the chain saw.

While Operating Saw

Essential safety guidelines to follow during chain saw operation.

Kickback Hazards

Explanation of kickback, its causes, and potential for severe injury.

Kickback Safety Devices

Information on built-in safety features designed to reduce kickback risk.

Maintenance and Kickback Safety

How proper maintenance influences kickback risk and overall safety.

Maintenance and Storage of Chain Saw

Pre-Service Checks and Maintenance

Safety steps before servicing and general saw inspection guidelines.

Care and Storage Procedures

Guidelines for maintaining the chain saw and storing it properly.

Unpacking

Checking Contents and Shipping Damage

Steps for removing items from the carton and checking for shipping damage.

Product Identification

Identifying Chain Saw Models

Diagrams illustrating parts of the RM1632A and RM1635W chain saw models.

Chain Saw Names and Terms

Glossary of Chain Saw Components

Definitions of key terms related to chain saw parts and operations.

Assembly

Guide Bar and Chain Assembly

Step-by-step instructions for attaching the guide bar and chain to the saw body.

Saw Chain Tension Adjustment

Adjusting Chain Tension

Procedure for properly tensioning the saw chain for safe operation.

Operating Chain Saw

Filling the Oil Tank

Instructions for filling the chain saw's oil reservoir with appropriate oil.

Oiling the Chain and Oil System

How to oil the chain and maintain the automatic oiling system.

Extension Cords

Guidelines for selecting and safely using extension cords with the saw.

Cutting with the Chain Saw

Techniques for making safe and effective cuts with the chain saw.

Felling a Tree

Detailed steps for safely cutting down a tree, including preparation and procedure.

Limbing a Tree

Instructions for safely removing branches from a fallen tree.

Bucking a Log

How to safely cut a log into sections, considering support and positioning.

Trimming a Tree (Pruning)

Steps for cutting limbs from a living tree, ensuring proper technique.

Cleaning and Maintenance

Cleaning the Saw Body

How to properly clean the exterior of the chain saw.

Guide Bar Maintenance

Procedures for cleaning and maintaining the guide bar for optimal performance.

Sharpening the Saw Chain

Instructions for sharpening the saw chain and its components.

Replacing the Saw Chain

Guidance on when and how to replace the saw chain.

Storage

Proper Storage Procedures

Steps for storing the chain saw safely for extended periods.

Repair Service

Obtaining Professional Repair

Information on how to get service from authorized dealers.

Troubleshooting

Common Chain Saw Problems and Solutions

A guide to diagnosing and fixing common issues with the chain saw.

Warranty Information

Manufacturers Limited Warranty

Details of the product's limited warranty, coverage, and exclusions.

Remington RM1635W Specifications

General IconGeneral
TypeElectric Chainsaw
Power SourceElectric
Bar Length16 inches
Weight9.7 lbs
Voltage120 V
Chain TypeLow-kickback
Chain Pitch3/8 inch
Chain Gauge0.050 inch

Related product manuals