REMKO RKL 495 DC - User Manual

Questions and Answers

T
Tammy JuarezAug 5, 2025
What to do if my REMKO RKL 495 DC does not start?
- A
  Alison WashingtonAug 5, 2025
  If your REMKO Air Conditioner doesn't start, there might be several reasons: * There could be a power failure. Check the voltage and wait until it is turned on again, if necessary. * The mains fuse or controller fuse might be faulty. Arrange to have it exchanged. * The power plug might not be inserted in the socket. Ensure the power plug is properly inserted. * The condensate container might be full, with a flashing "DRAIN WATER" display. Empty the container via the condensate drain hose. * The timer mode might be activated. Wait for the timer period to expire or press the "I / 0" key again.
A
Ashley BassAug 9, 2025
Why is my REMKO Air Conditioner working with reduced performance?
- M
  mccalllarryAug 9, 2025
  If your REMKO Air Conditioner is working with reduced performance, check the following: * Ensure that the exhaust air or outlet openings are not dirty or blocked. Clean the openings and remove any foreign objects. * The filter might be soiled. Clean the filter according to the instructions. * The outdoor unit might be dirty. Clean the fins on the inside of the outdoor unit. * The cooling load of the room might be excessive. Reduce the thermal load.
M
Michael HarrisAug 14, 2025
What to do if condensate leaks out of my REMKO Air Conditioner?
- S
  Stanley FitzpatrickAug 14, 2025
  If condensate leaks from your REMKO Air Conditioner, check if: * The unit is standing at an angle. Position it vertically and ensure it has a stable base. * The stopper in the condensate drain hose is missing. Seal the hose so that it is watertight again.
N
Nancy TrevinoAug 18, 2025
What does error code 32# mean on my REMKO RKL 495 DC Air Conditioner?
- M
  Matthew GeorgeAug 18, 2025
  Error code 32# on your REMKO Air Conditioner indicates a defective liquid line probe or excessive liquid line temperature. If the error appears less than 1 minute after turning on the unit, the THOP probe (PCB 3) is defective and needs replacement. If the error appears after operating for some time, it could be due to a lack of refrigerant or a malfunctioning fan motor in the outdoor unit. If the temperature on the THOP probe rises above 58 °C, the unit will switch off and display error code "32".
E
Eduardo HernandezAug 22, 2025
How to fix error code 01# on REMKO RKL 495 DC Air Conditioner?
- A
  allenhollandAug 22, 2025
  Error code 01# on a REMKO Air Conditioner indicates a communication error between the circuit board on the indoor unit and the outdoor unit. To resolve this, check the 6-wire connection and plug contacts CN202 (PCB 2) - CN109 (PCB 3). If necessary, replace the connecting cable or the motherboard (PCB 3).
R
Rebekah MorrisAug 27, 2025
What does error code 02# mean for REMKO RKL 495 DC Air Conditioner?
- R
  rogerjohnsonAug 27, 2025
  Error code 02# on your REMKO Air Conditioner means that the ambient temperature probe is defective. Replace the THRA probe (PCB 2).
E
Emily JacksonAug 30, 2025
What does error code 03# mean on a REMKO RKL 495 DC Air Conditioner?
- A
  ashleymurphyAug 30, 2025
  Error code 03# on your REMKO Air Conditioner indicates that the evaporator probe is defective. Replace the THEP probe (PCB 2).