Need help?Do you have a question about the Riello RESIDENCE KIS and is the answer not in the manual?
General| Fuel Type | Natural Gas / LPG |
|---|---|
| ErP Rating | A |
| Max Working Pressure | 3 bar |
| Ignition | Electronic |
| Heat Exchanger Material | Stainless Steel |
Crucial safety guidelines, user restrictions, and installation precautions for safe operation and maintenance.
Detailed procedures for installing the boiler, including system checks and connections.
Ensuring proper system function by cleaning and checking water parameters.
Provides technical specifications for boiler dimensions and weights.
Instructions for manually handling the boiler after unpacking.
Checks required when installing on older or updated systems.
Compliance with relevant standards for boiler installation.
Explanation of the standard automatic anti-freeze system and its limitations.
Details on connecting the condensation exhaust system to prevent gas escape.
Guidance on making low voltage and high voltage electrical connections.
Procedure for connecting the gas supply, ensuring correct gas type.
Explanation of the different operating modes for the variable speed circulator.
Guidance on using a traditional circulator in exceptional cases.
Procedure for performing a manual reset on the circulator.
Step-by-step guide to safely remove the boiler casing for access.
Requirements for flue gas evacuation and combustion air intake.
Guidance on using Ø80 flue gas exhaust pipe with different piping ranges.
Guidelines for installing the boiler on collective flues in positive pressure systems.
Instructions for safely draining the heating system.
Procedure for emptying the domestic hot water circuit to prevent frost damage.
Explanation of the condensate siphon's function and maintenance.
Parameters for interface settings like language, time, and scrolling text.
Parameters related to gas type, boiler type, and combustion settings.
Settings for hydraulic configuration, water pressure, and air purging.
Parameter to set the maximum heating setpoint.
Parameter to set the minimum heating setpoint.
Parameter to activate weather compensation.
Parameter to set the weather compensation curve.
Parameter to set the heating setpoint for zone 1.
Parameter to set the maximum heating setpoint for zone 1.
Parameter to set the minimum heating setpoint for zone 1.
Essential checks to perform before the first ignition and startup.
Steps for setting the time, day, and language of the boiler's control interface.
Description of the automatic vent cycle performed on boiler startup.
Detailed explanation of boiler configuration parameters and their settings.
Parameters for heating system control, including hysteresis and pump settings.
Parameter to set the maximum heating setpoint.
Parameter to set the minimum heating setpoint.
Parameter to activate weather compensation.
Parameter to set the weather compensation curve.
Adjusting the heating setpoint offset relative to the reference temperature.
Enabling and setting night compensation via the P4.20 parameter.
How the delivery setpoint is calculated with an OT chronostat.
How the delivery setpoint is calculated with a room thermostat.
Choosing the appropriate compensation curve for thermoregulation.
Setting the boiler to WINTER status for heating and hot water.
Setting the boiler to SUMMER status for domestic hot water only.
Setting the boiler to OFF status.
Activating the preheating function for domestic hot water.
Activating the Touch&Go function for on-demand hot water preheating.
Instruction for setting the maximum heating output value.
Instruction for setting the maximum heating output value.
Procedure for resetting the boiler after a fault.
Explanation of fault code E041 related to low pressure.
Explanation of fault code E060 related to DHW temperature stability.
Explanation of fault code E091 related to primary heat exchanger cleaning.
Detailed steps for cleaning the primary heat exchanger.
Detailed steps for cleaning the boiler's burner.
Instructions for cleaning the condensate siphon and SRD device.
Proper maintenance and replacement of the ionisation electrode.
Procedure for accessing and checking the boiler's check valve.
Step-by-step guide to removing the siphon and its components.
Note regarding combustion parameter variations after electrode maintenance.
Safety warning against using flammable cleaning agents.
Warning against using paint thinner for panels.
Instruction for cleaning panels using only soapy water.
Technical data related to the heating function of the boiler.
Technical data related to the domestic hot water (DHW) function.
Technical data specifically for combination heater functionality.
Information located on the boiler's serial number plate.
Specifications for the boiler's hydraulic connections.
Data related to the domestic hot water capacity.
Performance data for the boiler's fan.
Specifications for concentric flue gas outlet pipes.
Specifications for forced open installation configurations.
Boiler emission values for different operating outputs.
Maximum gas capacity for central heating.
Maximum gas capacity for domestic hot water.
Minimum gas capacity for central heating.
Minimum gas capacity for domestic hot water.
Fan rotation speed during slow ignition.
Maximum fan rotation speed for central heating.
Maximum fan rotation speed for domestic hot water.
Minimum fan rotation speed for CH/DHW.
Max CH fan rotations in C(10) configuration.
Max DHW fan rotations in C(10) configuration.
Min CH/DHW fan revolutions in C(10) configuration.
Energy efficiency class for space heating.
Energy efficiency class for water heating.
The maximum heat output of the boiler.
The energy efficiency of the boiler for space heating.
The useful heat output of the boiler.
The useful efficiency of the boiler for different operating conditions.
Electricity consumption of the boiler in different operating states.
Additional technical parameters of the boiler.
Technical data specifically for combination heater modes.
Information located on the boiler's serial number plate.
Explains the circulator's performance curve and anti-blocking function.
Graphs showing maximum flue and air pipe lengths based on bends and system configuration.
Graphs illustrating different thermoregulation curves for heating control.
Graphs for correcting the climate curve based on external factors.
Graphs showing parallel night time reduction for heating.
X-axis label: External temperature in degrees Celsius.
Y-axis label: Delivery temperature in degrees Celsius.
Graph illustrating the day temperature curve for heating.
Graph illustrating the night temperature curve for heating.
Setpoint for maximum heating temperature in standard systems.
Setpoint for maximum heating temperature in floor systems.
To Next Page