To Next PageTo Next PageWhat to do if my Rinnai HDC211e starts then shuts down immediately?
If your Rinnai Water Heater starts and then immediately shuts down, verify that the power is still on. Also, check that the gas isolation valves at the unit and the gas meter are fully open. Ensure your hot water tap is fully open as well.
What to do if my Rinnai HDC211e has no ignition or gas supply?
If your Rinnai Water Heater has no ignition or gas supply, check that the gas is turned on at both the water heater and the gas meter or cylinder.
Why does my Rinnai HDC211e Water Heater start and then the water goes cold?
If your Rinnai Water Heater starts and then the water goes cold, verify that the power is still on. Also, try opening your hot water tap further.
What to do if there is a power interruption during bath fill with my Rinnai HDC211e?
If there's a power interruption during a bath fill and water won't flow on power reinstatement with your Rinnai Water Heater, turn off all hot water taps and press the On/Off button twice.
How to fix Rinnai HDC211e Water Heater no ignition/no gas supply?
If your Rinnai Water Heater won't ignite due to a potential lack of gas supply, first, verify that the gas is turned on both at the water heater itself, and at the gas meter or cylinder.
What to do if Rinnai Water Heater has flame failure / low gas flow?
If you're experiencing flame failure or low gas flow with your Rinnai Water Heater, start by checking that the gas is turned on at both the water heater and the gas meter or cylinder. Also, ensure there are no obstructions blocking the flue outlet.
What to do if Rinnai HDC211e Water Heater does not start?
If your Rinnai Water Heater isn't starting, make sure the power is on at the unit and check that the isolation valves are open.
How to fix a noticeable reduction in water flow in my Rinnai HDC211e Water Heater?
If you notice a reduction in water flow in your Rinnai Water Heater, the inlet water filter may need to be cleaned. It is recommended to schedule a service call.
How to fix noticeable reduction in water flow in Rinnai HDC211e?
If you notice a reduction in water flow with your Rinnai Water Heater, the inlet water filter may need cleaning. A service call is recommended.
What to do if Rinnai HDC211e starts then the water goes cold?
If your Rinnai Water Heater starts but the water goes cold, verify that the power is still on and try opening your hot water tap further.
General| Brand | Rinnai |
|---|---|
| Model | HDC211e |
| Category | Water Heater |
| Language | English |
Specific installation requirements for Victorian consumers.
Pre-heats water in pipes for savings and reduced wait times.
Details features of Universal and Deluxe controllers.
Safety features limit temperature raising and priority transfer during hot water use.
Safety feature restricts kitchen controller priority return to 50°C if set above 50°C.
Explains automatic start/stop of burner via electronic ignition without controllers.
Factory pre-set temperatures vary by model and application; adjustable by authorized personnel.
Lists available temperatures and details Universal/Deluxe controller features.
Defines allowed combinations of Universal and Deluxe controllers.
Overview of the MC-91Q controller features and indicators.
Instructions for powering on the MC-91Q controller.
How to set the desired water temperature using the controller.
Guidance on operating multiple MC-91Q controllers and transferring priority.
Explains safety features related to temperature raising and priority transfer.
Overview of BC-100V controller features and indicators.
Instructions for powering on the BC-100V controller.
How to adjust voice prompt and audible tone settings.
Instructions for setting the 12-hour AM/PM clock.
How to set the desired water temperature using the controller.
How to use preset volume and temperature for shower or bath.
Steps to set desired temperature and water volume for the function.
How to manually stop the shower/bath fill function.
How Universal and Deluxe controllers can be used together.
Overview of MC-100V kitchen controller features and indicators.
Instructions for powering on the MC-100V kitchen controller.
How to adjust voice prompt and audible tone settings for the kitchen controller.
Instructions for setting the 12-hour AM/PM clock for the kitchen controller.
How to set the desired water temperature using the kitchen controller.
Overview of the Smartstart® system and its benefits.
Step-by-step guide to activating the preheat function.
Lists error codes, faults, and recommended remedies.
Common issues and solutions when no controllers are fitted.
Covers regulations, applicable models, and appliance location.
Guidance on selecting appropriate gas and water pipe sizes.
Requirements for water pressure and quality.
Regulations regarding temperature limits for personal hygiene.
How to install heaters and controllers based on temperature requirements.
Installation must comply with AS/NZS standards and local regulations.
Guidelines for outdoor and indoor installation locations.
Optimal placement for efficiency and accessibility.
Details on water pressure, approved valves, and quality.
When temperature limiting devices are required for installation.
Instructions for securely mounting the water heater unit.
Details required valves, unions, and connections.
Specifies minimum clearances around horizontal flue terminals.
Minimum clearance requirements for horizontal obstructions near flue terminals.
How to install multiple external units side-by-side.
Provides detailed dimensions for various models and controllers.
Installation guidance for internal model flue systems.
Describes four basic flue installation methods.
Clearance rules for side-by-side terminal installations.
Material recommendations and important notes for condensate piping.
Guidelines for condensate drain pipe length and changes of direction.
Specific installation requirements for condensate drain lines.
How to join condensate drain lines from multiple heaters.
How to discharge condensate into a common stack in multi-storey buildings.
Requirements for drain lines connected to a tundish.
Precautions for areas prone to freezing.
Notes compatibility and optional nature of Rinnai controllers.
Guidelines for ideal placement of controllers for optimal performance and safety.
Information on voltage, cable length, and extension options.
Step-by-step guide to installing the MC-91Q controller.
Programming for connecting 4 controllers and temperature limits.
Step-by-step guide to installing the MC-100V controller.
Step-by-step guide to installing the BC-100V controller.
How to connect controller cables to the main unit.
Procedures for testing gas, water, and controller functions post-installation.
Explains factory settings and incremental adjustments for delivery temperature.
Guidance on adjusting gas pressure if the unit is not operating correctly.
Mentions a checklist on the appliance front cover for correct commissioning.
Accessory for recessing the appliance into a wall.
Accessory to conceal plumbing pipe-work.
Accessory for protecting the unit from theft/damage.
Accessory for securing the unit against theft.
Accessory to redirect flue products on balconies.
