To Next PageTo Next PageWhat to do if Rinnai REU-AM2626WDL Water Heater water doesn't flow after a power interruption during bath fill?
If your Rinnai Water Heater experiences a power interruption while filling a bath and water doesn't flow when power is restored, turn off all hot water taps, then press the On/Off button twice.
Why does my Rinnai REU-AM2626WDL Water Heater have flame failure or low gas flow?
If you are experiencing flame failure or low gas flow with your Rinnai Water Heater, verify that the gas is turned on at both the water heater and the gas meter or cylinder. Also, check for any obstructions to the flue outlet.
What causes a Rinnai REU-AM2626WDL wireless controller to be out of range?
If fitted, a Rinnai Water Heater's wireless water controller might be ‘Out of Range’ because of the distance from the transceiver or an obstruction. To resolve this, try moving the wireless water controller or transceiver, or remove any obstructions.
General| Type | Tankless |
|---|---|
| Fuel Type | Gas |
| Gas Type | Natural Gas |
| Dimensions | 23.6 x 13.8 x 9.4 inches |
| Weight | 50 lbs |
| Energy Factor | 0.82 |
| Venting | Direct Vent |
| Ignition Type | Electronic Ignition |
| Temperature Range | 98°F to 140°F |
| Maximum Input | 199, 000 BTU/h |
| Minimum Input | 15, 000 BTU/h |
| Vent Diameter | 3" |
| Electrical Requirements | 120V AC, 60Hz |
| Maximum BTU | 199, 000 |
| Warranty | 12 years heat exchanger, 5 years parts |
Details Rinnai's certification by the Australian Gas Association and installation compliance.
Advises Victorian consumers on the requirement for licensed installers and compliance certificates.
Highlights the danger of scalding hazards, especially for vulnerable individuals.
Covers safe operation for persons with reduced capabilities and supervision of children.
Outlines the key advantages and technological features of the Rinnai continuous flow water heater.
Explains factory pre-set temperatures and how they can be adjusted by authorized personnel.
Describes how the appliance operates automatically when taps are opened and closed.
States compatibility and usage guidelines for Rinnai water controllers.
Details user-controlled temperature settings and limitations for Master and Sub controllers.
Specifies the maximum number and types of water controllers that can be installed.
Provides operational instructions for the Universal Water Controller (MC-601Q).
Explains how the Smartstart system warms water in pipes for immediate hot water.
Step-by-step guide for activating and using the Smartstart preheat function.
Notes that controller functions are unaffected by preheat operation.
Lists diagnostic error codes and their potential remedies for the water heater.
Troubleshooting steps for a wireless water controller with no power display.
Provides solutions for common symptoms when operating without water controllers.
Specifies installation compliance with AS/NZS standards and local regulations.
States that instructions apply to Rinnai Continuous Flow Water Heater models listed on the cover.
Guidance on selecting an appropriate outdoor location for the appliance.
Instructions on how to securely mount the water heater unit to a vertical structure.
Details requirements for water and gas inlet connections, including isolation valves.
Guidance on gas and water pipe sizing for optimal performance and efficiency.
Information on water supply requirements, pressure limitations, and water quality.
Addresses temperature limitations for personal hygiene areas and installation configurations.
Illustrates installation setups based on 50°C compliance and local regulations.
Specifies horizontal terminal clearances from building structures and openings.
Details minimum horizontal clearance requirements to avoid obstructing the appliance.
Instructions for fitting a Sideways Flue Diverter and associated control board settings.
Clarifies flue terminal clearance rules for multiple appliance installations.
States compatibility and authorization requirements for water controller installation.
Defines Master/Sub controller roles and temperature settings, including limits.
Outlines limitations on the number and types of water controllers that can be fitted.
Provides guidelines for the optimal and safe placement of water controllers.
Details the use of Rinnai supplied communication cables for wired controllers.
Instructions for connecting communication cables to the water heater's 'Ezi connect'.
Step-by-step guide for installing the Universal Water Controller (MC-601Q).
Covers programming for four controllers and non-50°C compliant models.
Procedure for testing the water heater after installation, including leak and pressure checks.
Explains factory settings and adjustment mechanisms for delivery temperatures.
Information on the electronic gas regulator and when adjustments might be needed.
Indicates the location of the wiring diagram for installation reference.
Highlights the availability of a checklist to ensure correct commissioning.
Emphasizes the importance of the installation record for service and reference.
Provides detailed physical dimensions for various Rinnai water heater models.
Lists technical data including gas rate, water pressure, flow rates, and connections.
Shows factory pre-set and adjustable maximum delivery temperatures for models.
Lists available accessory options for Rinnai Continuous Flow Water Heaters.
