To Next PageTo Next Page
Need help?Do you have a question about the Rinnai V65i and is the answer not in the manual?
General| Type | Tankless |
|---|---|
| Fuel Type | Natural Gas or Propane |
| Installation Location | Indoor |
| Energy Factor | 0.82 |
| Weight | 45.6 lbs |
| Temperature Range | 98°F - 140°F |
| Voltage | 120V |
| Thermal Efficiency | 82% |
| Dimensions | 23 x 14 x 9 inches |
| BTU Input Range | 15, 000 - 150, 000 BTU/h |
| Venting | Direct Vent |
| Ignition System | Electronic |
| Ignition Type | Electronic |
| Warranty | 5 years parts |
| Flow Rate | Up to 6.5 GPM |
Defines safety alert symbols like DANGER, WARNING, and CAUTION.
Outlines skills required for professional installation.
Specifies types of installations supported (residential, mobile homes).
Lists the sequence of installation tasks.
Provides essential do's and don'ts for installation.
Details parts, tools, and materials needed for installation.
Guides selection of suitable locations considering clearances and environment.
Discusses water quality impact on the heat exchanger and warranty.
Advises on avoiding corrosive environments for installation.
Specifies required clearances for vent termination for indoor models.
Details specific clearances for indoor models V75i and V65i.
Details specific clearances for outdoor models V75e and V65e.
Presents clearance requirements for indoor and outdoor models in a table.
Explains how to determine and set maximum vent length based on elbows.
Advises on protecting the unit and water lines from freezing.
Provides a checklist for verifying installation location suitability.
Details the process of securely mounting the water heater to the wall.
Instructs on removing the front panel for access.
Covers guidelines and manufacturers for installing venting systems.
Illustrates and explains flue termination methods, with or without condensate collector.
Explains condensate formation and drainage requirements for indoor models.
Checklist to ensure proper venting and condensate management.
Details requirements for installing pressure relief valves.
Recommends installing isolation valves for easier maintenance.
Outlines rules for potable water piping and connections.
Shows a schematic of basic water and gas connections.
Explains how to connect the water heater to the water supply lines.
A checklist to verify proper plumbing installation.
Provides essential do's and don'ts for gas supply installation.
Details how to size gas piping based on consumption and length.
Explains how to set DIP switches for different altitudes.
Instructs on adjusting DIP switch for vent length.
Checklist to confirm correct gas and electrical connections.
Explains how multiple controllers can be wired in parallel.
Advises on selecting suitable locations for temperature controllers.
Specifies cable gauge and maximum lengths for controllers.
Provides step-by-step instructions for mounting the controller.
Lists detailed technical specifications for various models.
Provides physical dimensions of the water heaters.
Graph showing pressure loss versus water flow rate.
Graph showing water flow rate versus temperature rise.
Provides introductory facts and safety advice for operation.
Outlines emergency procedures for gas leaks.
Step-by-step guide for starting and operating the water heater.
Instructions for safely shutting off gas to the appliance.
Lists available temperature settings with and without a controller.
Explains temperature settings without a controller.
How to enable/disable audible beeps on the controller.
Instructions for locking and unlocking the controller.
How to access and view diagnostic codes.
Instructions for cleaning internal and external parts of the appliance.
Advises on annual inspection of the vent system.
Notes on motor lubrication and cleaning.
Cleaning instructions for the temperature controller.
Addresses diagnostic codes related to scale build-up and flushing.
Reminds to keep the flue terminal clear of snow.
Instructions for cleaning the inlet water filter.
Instructions for annual manual testing of the pressure relief valve.
How to visually inspect the burner flame for proper operation.
Advice on protecting the unit from freezing weather.
Recommendations for preparing the unit for winter.
Step-by-step instructions for manually draining the unit.
Steps to follow after draining to return to normal operation.
Method to prevent freezing by running low water volume.
Actions to take if the unit or piping has frozen.
Important notice regarding licensed professional installation.
Specific regulations for Massachusetts installation.
Details the terms and scope of the limited warranty.
Specifies what defects are covered under the warranty.
Outlines the duration of warranty coverage for different components.
Explains Rinnai's responsibilities for repairs and replacements.
Provides instructions on how to obtain warranty service.
Lists exclusions and limitations of the warranty.
Discusses implied warranties and legal rights.
