To Next PageTo Next PageWhat to do if my Rinnai Water Heater starts then shuts down immediately?
If your Rinnai Water Heater starts and then immediately shuts down, verify that the power is still on. Also, check that the gas isolation valves at the unit and the gas meter are fully open. Ensure your hot water tap is fully open as well.
What to do if my Rinnai Water Heater has no ignition or gas supply?
If your Rinnai Water Heater has no ignition or gas supply, check that the gas is turned on at both the water heater and the gas meter or cylinder.
Why does my Rinnai REU-VR2626WB start and then the water goes cold?
If your Rinnai Water Heater starts and then the water goes cold, verify that the power is still on. Also, try opening your hot water tap further.
What to do if there is a power interruption during bath fill with my Rinnai REU-VR2626WB?
If there's a power interruption during a bath fill and water won't flow on power reinstatement with your Rinnai Water Heater, turn off all hot water taps and press the On/Off button twice.
How to fix Rinnai REU-VR2626WB Water Heater no ignition/no gas supply?
If your Rinnai Water Heater won't ignite due to a potential lack of gas supply, first, verify that the gas is turned on both at the water heater itself, and at the gas meter or cylinder.
What to do if Rinnai REU-VR2626WB has flame failure / low gas flow?
If you're experiencing flame failure or low gas flow with your Rinnai Water Heater, start by checking that the gas is turned on at both the water heater and the gas meter or cylinder. Also, ensure there are no obstructions blocking the flue outlet.
What to do if Rinnai REU-VR2626WB does not start?
If your Rinnai Water Heater isn't starting, make sure the power is on at the unit and check that the isolation valves are open.
How to fix a noticeable reduction in water flow in my Rinnai REU-VR2626WB Water Heater?
If you notice a reduction in water flow in your Rinnai Water Heater, the inlet water filter may need to be cleaned. It is recommended to schedule a service call.
How to fix noticeable reduction in water flow in Rinnai Water Heater?
If you notice a reduction in water flow with your Rinnai Water Heater, the inlet water filter may need cleaning. A service call is recommended.
What to do if Rinnai REU-VR2626WB starts then the water goes cold?
If your Rinnai Water Heater starts but the water goes cold, verify that the power is still on and try opening your hot water tap further.
General| Type | Tankless |
|---|---|
| Fuel Type | Natural Gas |
| Gas Type | Natural Gas |
| Minimum BTU Input | 15, 000 BTU/hr |
| Energy Factor | 0.82 |
| Voltage | 120V |
| Ignition Type | Electronic Ignition |
| Venting | Direct Vent |
| Heating Capacity | 199, 000 BTU/h |
| Energy Efficiency | 0.82 |
| Maximum BTU Input | 199, 000 BTU/hr |
| Temperature Range | 98°F - 185°F |
| Warranty | 12 years heat exchanger, 5 years parts |
Advisory for Victorian consumers regarding installation licensing requirements.
Critical safety information regarding scalding hazards from hot water.
Details factory pre-set maximum delivery temperatures for various models.
Explains combinations of Universal and Deluxe water controllers.
Overview of the Universal Water Controller, its indicators, and buttons.
Guides on turning on the controller and adjusting water temperature.
Explains how to manage multiple controllers and transfer priority.
Overview of the Deluxe Bathroom Water Controller, its features and indicators.
Instructions for setting sound options and the clock on the controller.
Guidance on adjusting the water temperature using the controller.
Details on using the automatic shower saver and bath fill features.
Overview of the Deluxe Kitchen Water Controller, its features and indicators.
Guides on configuring sound, clock, and adjusting water temperature.
Explains the purpose and benefits of the Smartstart® preheat system.
Step-by-step guide on how to activate the preheat function.
Lists error codes, their faults, and recommended remedies for diagnosis.
Provides solutions for common issues when no water controllers are fitted.
Covers installation compliance, applicable models, and siting requirements.
Details on water pipe sizing, supply pressure, and hot water delivery temperature.
Instructions for appliance mounting and service connection points.
Specifies minimum clearances around horizontal flue terminals for safety.
Covers clearances for obstructions and guidelines for installing multiple units.
Provides detailed dimensions for appliances and water controllers.
Specific instructions for installing co-axial flue systems for internal units.
Specific instructions for draining condensate from REU-KM' models.
Guidelines on compatibility, ideal placement, and cable connections for controllers.
Step-by-step instructions for installing Universal and Deluxe controllers.
Specific fitting instructions for Deluxe Kitchen and Bathroom controllers.
Procedures for connecting controller communication cables to the main unit.
Procedures for testing the appliance and verifying delivery temperatures.
Details on setting gas pressure and using commissioning checklists for proper setup.
