To Next PageTo Next PageWhat to do if my Rinnai REU-VRM2632FFUC Water Heater starts then shuts down immediately?
If your Rinnai Water Heater starts and then shuts down immediately, ensure the power is still on. Also, check that the gas isolation valves at the unit and the gas meter are fully open. Finally, make sure to open your hot water tap fully.
What to do if my Rinnai Water Heater has no ignition or gas supply?
If your Rinnai Water Heater has no ignition or gas supply, check that the gas is turned on at both the water heater and the gas meter or cylinder.
What to do if my Rinnai Water Heater starts then the water goes cold?
If your Rinnai Water Heater starts but the water goes cold, verify that the power is still on. Additionally, try opening your hot water tap further.
Why does my Rinnai REU-VRM2632FFUC Water Heater start and then the water goes cold?
If your Rinnai Water Heater starts and then the water goes cold, verify that the power is still on. Also, try opening your hot water tap further.
What to do if there is a power interruption during bath fill with my Rinnai REU-VRM2632FFUC?
If there's a power interruption during a bath fill and water won't flow on power reinstatement with your Rinnai Water Heater, turn off all hot water taps and press the On/Off button twice.
How to fix Rinnai REU-VRM2632FFUC no ignition/no gas supply?
If your Rinnai Water Heater won't ignite due to a potential lack of gas supply, first, verify that the gas is turned on both at the water heater itself, and at the gas meter or cylinder.
What to do if Rinnai REU-VRM2632FFUC has flame failure / low gas flow?
If you're experiencing flame failure or low gas flow with your Rinnai Water Heater, start by checking that the gas is turned on at both the water heater and the gas meter or cylinder. Also, ensure there are no obstructions blocking the flue outlet.
What to do if Rinnai REU-VRM2632FFUC Water Heater does not start?
If your Rinnai Water Heater isn't starting, make sure the power is on at the unit and check that the isolation valves are open.
What to do if my Rinnai REU-VRM2632FFUC does not attempt to start at all?
If your Rinnai Water Heater does not attempt to start at all, check that the power is on at the unit. Also, ensure that the isolation valves at the unit are open.
What to do if there is power interruption during bath fill with my Rinnai REU-VRM2632FFUC Water Heater?
If you experience a power interruption during a bath fill and the water will not flow when the power is restored, turn off all hot water taps. Then, press the On/Off button twice.
General| Brand | Rinnai |
|---|---|
| Model | REU-VRM2632FFUC |
| Category | Water Heater |
| Language | English |
Information for Victorian consumers regarding licensed installation.
Critical warnings about hot water hazards and scalding.
Notes solar incompatibility, low flow, freezing, and flue outlet safety.
Covers controller cleaning, temperature limits, and warnings.
Explains appliance operation without controllers and safety.
Details factory pre-set temperatures and model specifications.
Explains controller operations, temperature ranges, and combinations.
Describes the MC-91Q controller, its indicators, and basic functions.
Covers multi-controller operation, priority transfer, and limitations.
Describes the BC-100V controller, its basic functions, and priority.
Covers sound, clock, temperature settings, and safety checks.
Instructions for using the Shower Saver/Bath Fill feature, including settings and recommendations.
Describes the MC-100V controller, its basic functions, and settings.
Guide for setting the clock and adjusting water temperature.
Explains the Smartstart® system, how to activate, and manage its functions.
Lists error codes, remedies, and troubleshooting without controllers.
Covers regulations, model applicability, and appliance location.
Details coaxial flueing for internal models and flue terminal clearances.
Addresses pipe sizing, water supply, and delivery temperature considerations.
Covers appliance mounting, service points, and horizontal obstructions.
Notes on installing multiple units and provides appliance dimensions.
Discusses drain pipe material, length, direction, and discharge points.
Covers common stack discharge, tundish lines, and freezing area requirements.
Guidance on positioning controllers and connecting cables.
Step-by-step guides for installing Universal, Deluxe Kitchen, and Deluxe Bathroom controllers.
Instructions for connecting controller communication cables to the appliance.
Procedures for testing, verifying temperature, and setting gas pressure.
Reference to available commissioning checklists for installers.
