Riso HC5500 - Page 47

Temporary image adjustment method (manual adjustment) Item 21-2
[ Vertical image adjustment ]
This function is available on “HC5500 firmware Ver2.02” or later.
In addition, controller veision is required the following version or later.
HC3R-5000; Ver1.30 PS7R-9000; Ver3.30
[ Vertical image adjustment ]
Point
SE mode 5.6.9
- Move for 1 drop when input 16 point.
- Move for head direction when input numerical value of minus.
- Input numerical same value that is gap quantity.
Case of Cyan 1 head
First, Input value that is joined with original value and 8 by SE mode 8.5.1.7.13
Next, Input value that is joined with original value and 8 by SE mode 8.5.1.7.14
㪪㪜㩷㫄㫆㪻㪼㩷㪌㪅㪍㪅㪐
㩷㩷㩷㪪㫀㫑㪼㩷㪘㪊㩷
㪟㪼㪸㪻㪈㪄㪈㪆㪈㪄㪉㩷 㪟㪼㪸㪻㪉㪄㪈㪆㪉㪄㪉㩷 㪟㪼㪸㪻㪊㪄㪈㪆㪊㪄㪉㩷
䋱㪻㫉㫆㫇㩷㪔㩷㪈㪍㫇㫆㫀㫅㫋㩷
㪞㪸㫇㩷㫆㪽㩷㪻㫉㫆㫇㩷㫇㫆㫊㫀㫋㫀㫆㫅㩷㫀㫊㩷㪸㪹㫆㫌㫋㩷㪏㩷㫇㫆㫀㫅㫋㩷
㪧㫉㫀㫅㫋㩷㪻㫀㫉㪼㪺㫋㫀㫆㫅㩷
㪧㫉㫀㫅㫋㩷㪻㫀㫉㪼㪺㫋㫀㫆㫅㩷
㪟㪼㪸㪻㪈㪄㪈㪆㪈㪄㪉㩷 㪟㪼㪸㪻㪉㪄㪈㪆㪉㪄㪉㩷 㪟㪼㪸㪻㪊㪄㪈㪆㪊㪄㪉㩷
㪛㫉㫆㫇㩷㫇㫆㫊㫀㫋㫀㫆㫅㩷㫀㫊㩷㫑㫀㪾㫑㪸㪾㪅㩷
㪧㫉㫀㫅㫋㩷㪻㫀㫉㪼㪺㫋㫀㫆㫅㩷
㪟㪼㪸㪻㪈㪄㪈㪆㪈㪄㪉㩷 㪟㪼㪸㪻㪉㪄㪈㪆㪉㪄㪉㩷 㪟㪼㪸㪻㪊㪄㪈㪆㪊㪄㪉㩷
㪞㪸㫇㩷㫆㪽㩷㪻㫉㫆㫇㩷㫇㫆㫊㫀㫋㫀㫆㫅㩷㫀㫊㩷㫅㫆㫋㪿㫀㫅㪾㪅㩷
Check here