RITE-HITE Genisys GWC-1000 User Manual

BLACK
(SW1)
BROWN
(+12V)
BLUE
(COM)
BLACK
(SO)
SENSOR
CABLE
GREY
(CAPPED)
WHITE
(CAPPED)
WHITE
(CAPPED)
BLUE
(COM)
BROWN
(+12V)
COIL CABLE TO SENSOR
JUNCTION BOX WIRING
NOTES:
STEP 7
1) FEED CORD BACK THROUGH THE BRACKET AS SHOWN.
2) ROUTE CORD THROUGH 90° CORDGRIP AND INSTALL ONTO CONDUIT BOX
AS SHOWN.
3) ZIP TIE CORD TO BRACKET AS SHOWN (ZIP TIE SUPPLIED BY OTHERS).
4) REINSTALL STRAIGHT CORDGRIP TO BRACKET AS SHOWN.
STEP 8
1) REWIRE CORDS IN CONDUIT BOX AS SHOWN ON WIRING DIAGRAM TO RIGHT.
N
OT
R
EL
EAS
E
D
CONFIDENTIAL
PRODUCTS CORPORATION.
=
PRODUCTS CORPORATION
REV
SHEET
TITLE
SIZE
SCALE
DWG NO
®
© 2019 RITE-HITE®
REVISION STATUS
DRAWN BY
RESPONSIBLE ENGINEER
DO NOT SCALE DRAWING
MATERIAL
INSTR MODFY GWC1 BARR ORIENT
C
0159009
--
1:2 4 OF 6
THIRD ANGLE PROJECTION
.060
.X
.030
ALL SHEETS ARE THE SAME
.XX
TOLERANCES:
A
B
C
D
D
C
B
A
4
3
2
1
4
321
UNLESS OTHERWISE SPECIFIED
.XXX
ANGLE
MANUFACTURING ENGINEER
B. WIEBERDINK
=
FINISH
DIMENSIONS ARE IN INCHES.
REFERENCE
2.0
WEIGHT
G. PROFFITT
= .120
=
THIS DOCUMENT IS THE PROPERTY
OF RITE-HITE® PRODUCTS
CORPORATION SUBJECT MATTER
HEREIN IS CONFIDENTIAL. DO NOT
USE, REPRODUCE, COPY OR
DISCLOSE EXCEPT WITH WRITTEN
CONSENT OF RITE-HITE®
PRODUCTS CORPORATION
90° CORDGRIP
ZIP TIE
STEP 7
CORD
(SUPPLIED BY OTHERS)
STRAIGHT
CORDGRIP
STEP 8
REV DATE DESCRIPTION ECN APPROVED BY
A 06/05/2019 RELEASE TO PRODUCTION 20190145 G. PROFFITT
REVISION HISTORY
G1
G3
G2
Zip Tie (supplied by others)
BLACK
(SW1)
BROWN
(+12V)
BLUE
(COM)
BLACK
(SO)
SENSOR
CABLE
GREY
(CAPPED)
WHITE
(CAPPED)
WHITE
(CAPPED)
BLUE
(COM)
BROWN
(+12V)
COIL CABLE TO SENSOR
JUNCTION BOX WIRING
NOTES:
STEP 7
1) FEED CORD BACK THROUGH THE BRACKET AS SHOWN.
2) ROUTE CORD THROUGH 90° CORDGRIP AND INSTALL ONTO CONDUIT BOX
AS SHOWN.
3) ZIP TIE CORD TO BRACKET AS SHOWN (ZIP TIE SUPPLIED BY OTHERS).
4) REINSTALL STRAIGHT CORDGRIP TO BRACKET AS SHOWN.
STEP 8
1) REWIRE CORDS IN CONDUIT BOX AS SHOWN ON WIRING DIAGRAM TO RIGHT.
N
OT
R
EL
EAS
E
D
CONFIDENTIAL
PRODUCTS CORPORATION.
=
PRODUCTS CORPORATION
REV
SHEET
TITLE
SIZE
SCALE
DWG NO
®
© 2019 RITE-HITE®
REVISION STATUS
DRAWN BY
RESPONSIBLE ENGINEER
DO NOT SCALE DRAWING
MATERIAL
INSTR MODFY GWC1 BARR ORIENT
C
0159009
--
1:2 4 OF 6
THIRD ANGLE PROJECTION
.060
.X
.030
ALL SHEETS ARE THE SAME
.XX
TOLERANCES:
A
B
C
D
D
C
B
A
4
3
2
1
4
321
UNLESS OTHERWISE SPECIFIED
.XXX
ANGLE
MANUFACTURING ENGINEER
B. WIEBERDINK
=
FINISH
DIMENSIONS ARE IN INCHES.
REFERENCE
2.0
WEIGHT
G. PROFFITT
= .120
=
THIS DOCUMENT IS THE PROPERTY
OF RITE-HITE® PRODUCTS
CORPORATION SUBJECT MATTER
HEREIN IS CONFIDENTIAL. DO NOT
USE, REPRODUCE, COPY OR
DISCLOSE EXCEPT WITH WRITTEN
CONSENT OF RITE-HITE®
PRODUCTS CORPORATION
90° CORDGRIP
ZIP TIE
STEP 7
CORD
(SUPPLIED BY OTHERS)
STRAIGHT
CORDGRIP
STEP 8
REV DATE DESCRIPTION ECN APPROVED BY
A 06/05/2019 RELEASE TO PRODUCTION 20190145 G. PROFFITT
REVISION HISTORY
BLACK
(SW1)
BROWN
(+12V)
BLUE
(COM)
BLACK
(SO)
SENSOR
CABLE
GREY
(CAPPED)
WHITE
(CAPPED)
WHITE
(CAPPED)
BLUE
(COM)
BROWN
(+12V)
COIL CABLE TO SENSOR
JUNCTION BOX WIRING
NOTES:
STEP 7
1) FEED CORD BACK THROUGH THE BRACKET AS SHOWN.
2) ROUTE CORD THROUGH 90° CORDGRIP AND INSTALL ONTO CONDUIT BOX
AS SHOWN.
3) ZIP TIE CORD TO BRACKET AS SHOWN (ZIP TIE SUPPLIED BY OTHERS).
4) REINSTALL STRAIGHT CORDGRIP TO BRACKET AS SHOWN.
STEP 8
1) REWIRE CORDS IN CONDUIT BOX AS SHOWN ON WIRING DIAGRAM TO RIGHT.
N
OT
R
EL
EAS
E
D
CONFIDENTIAL
PRODUCTS CORPORATION.
=
PRODUCTS CORPORATION
REV
SHEET
TITLE
SIZE
SCALE
DWG NO
®
© 2019 RITE-HITE®
REVISION STATUS
DRAWN BY
RESPONSIBLE ENGINEER
DO NOT SCALE DRAWING
MATERIAL
INSTR MODFY GWC1 BARR ORIENT
C
0159009
--
1:2 4 OF 6
THIRD ANGLE PROJECTION
.060
.X
.030
ALL SHEETS ARE THE SAME
.XX
TOLERANCES:
A
B
C
D
D
C
B
A
4
3
2
1
4
321
UNLESS OTHERWISE SPECIFIED
.XXX
ANGLE
MANUFACTURING ENGINEER
B. WIEBERDINK
=
FINISH
DIMENSIONS ARE IN INCHES.
REFERENCE
2.0
WEIGHT
G. PROFFITT
= .120
=
THIS DOCUMENT IS THE PROPERTY
OF RITE-HITE® PRODUCTS
CORPORATION SUBJECT MATTER
HEREIN IS CONFIDENTIAL. DO NOT
USE, REPRODUCE, COPY OR
DISCLOSE EXCEPT WITH WRITTEN
CONSENT OF RITE-HITE®
PRODUCTS CORPORATION
90° CORDGRIP
ZIP TIE
STEP 7
CORD
(SUPPLIED BY OTHERS)
STRAIGHT
CORDGRIP
STEP 8
REV DATE DESCRIPTION ECN APPROVED BY
A 06/05/2019 RELEASE TO PRODUCTION 20190145 G. PROFFITT
REVISION HISTORY
Coil Cable to Sensor
Sensor Cable
Brown
(+12V)
Black (SWI)
White
(CAPPED)
Brown (+12V)
Black (SO)
Grey (CAPPED)
White
(CAPPED)
Blue (COM)
Blue (COM)
4. Reassemble as shown:
• Leave straight cord grip (G3) on cord (G2) and feed
cord back through the bracket.
• Route cord through 90°cord grip (G1) and install
onto junction box.
• Use zip tie (supplied by others) to fasten cord to
bracket.
• Reinstall straight cord grip to bracket
5. (I) Rewire cords in junction box as shown on wiring
diagram.
Figure 4
INSTALLATION
Change Orientation Continued
I
Genisys™ GWC-1000 Global Wheel Chock Installation/Service/Owner's Manual Rite-Hite
®
6 Publication: AMEN00274 2020-06-26

RITE-HITE Genisys GWC-1000 Specifications

General

Brand	RITE-HITE
Model	Genisys GWC-1000
Category	Automobile Accessories
Language	English