EasyManuals Logo

Roborock S8 MaxV Ultra User Manual

Roborock S8 MaxV Ultra
48 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #13 background imageLoading...
Page #13 background image
13
Drying starts automatically after mop
washing or after cleaning is completed.
To manually start or stop drying, tap the
corresponding button in the app.
Notes:
Ŏ
Stay away from the drying air outlets during drying.
Ŏ
Drying duration can be modified in the app.
Ŏ
Auto-drying can be disabled in the app.
Drying
$
Note: Smart Cleaning Solution Filling can be disabled
in the app.
The robot will automatically add cleaning
solution to the water for mop washing and
robot water tank refilling according to the
preset ratio to ensure optimal mopping
performance.
Auto Cleaning Solution Addition
$
Note: If the robot fails to find the dock, it will automatically
return to its starting position. Place the robot on the
dock manually to recharge.
After cleaning, the robot will automatically
return to the dock to charge.
Press
to send the paused robot back
to the dock. The power indicator light will
breathe during robot charging.
Charging
$
The default Do Not Disturb (DND) period is
from 22:00 to 08:00. You can use the app to
disable the DND mode or modify the DND
DND Mode
$
Press and hold to enable/disable Child
Lock. You can also set it in the app. Once
enabled, the robot will not react to button
presses when it is stationary. When the
robot is cleaning or docking, press any
button to pause it.
If an error occurs, the power indicator light
on the robot will flash red or status indicator
light on the dock will be steady red. A pop-
up notification will appear in the app and a
voice alert may sound.
If the robot does not respond when a button
is pressed or cannot be turned off, reset the
system by pressing the Reset button.
Note: After resetting the system, existing settings such
as scheduled cleaning and WiFi will be restored to
factory settings.
If the robot does not function properly after
a system reset, switch it on. Press and hold
and at the same time, press the Reset
button until you hear the “Restoring
factory settings” voice message. The robot
will then be restored to factory settings.
Child Lock
$
Error
$
Resetting the System
$
Restoring Factory Settings
$
Notes:
Ŏ
The robot will go to sleep automatically if left in a
malfunctioning state for over 10 minutes.
Ŏ
Placing a malfunctioning robot on the dock manually
will end the current cleanup.
Note: The frequency of replacement may vary with the
actual situation. If abnormal wear occurs, replace the
parts immediately.
*
Clean every 2 weeks and replace every 6-12 months.
Main Brushes
%
Routine Maintenance
D
D1-1—Hair-Blocking Rings
D1-2—Main Brush Caps
D1-3—Main Brush Cover
D1-4—Latches
D1-5—Main Brushes
D1-6—Main Brush Bearing
Turn over the robot and press the
two latches inwards to remove the
main brush cover.
D1-7—
Pull out the main brushes and
remove the main brush bearings,
main brush caps, and hair-blocking
rings. Remove any entangled hair
or dirt at both ends of the main
brushes. Then, reinstall the hair-
blocking rings, main brush caps, and
main brush bearings.
D1-8—
period, or set whether to enable auto top-
up, emptying and drying, to dim the button
light, or lower the volume of the voice
message during the DND period.

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Roborock S8 MaxV Ultra and is the answer not in the manual?

Roborock S8 MaxV Ultra Specifications

General IconGeneral
Package typeBox
Package depth479 mm
Package width494 mm
Package height428 mm
Package weight17400 g
Product colorWhite
Remotely operatedYes
Dust container typeCombi
Brush typeRoller brush & Side brush
Noise level67 dB
Frequency band2.4 GHz
Navigation typeLiDAR
Integrated sensorsCamera
Water tank capacity0.1 L
Dust capacity (base)2.5 L
Dust capacity (total)2.77 L
HEPA filtration system-
Floor surfaces supportedCarpet, Hard floor
Threshold climbing (max)20 mm
Dust capacity (vacuum cleaner)0.27 L
Battery life300 m²
Charging time4 h
Battery capacity5200 mAh
Power consumption (typical)60 W
Suction power10000 Pa
Weight and Dimensions IconWeight and Dimensions
Depth353 mm
Width350 mm
Height103 mm
Base station dimensions (W x D x H)409 x 419 x 300 mm

Related product manuals