Rockville RAM15BT V2 User Manual (English)

Questions and Answers:

J
john40Aug 15, 2025
How to fix Bluetooth pairing fails on Rockville Speakers?
- K
  Kathleen JohnsonAug 15, 2025
  To resolve Bluetooth pairing issues with your Rockville Speakers: * Ensure both devices are on and your Bluetooth device is discoverable. * Try turning both devices off and on again. * Select the correct source. * Keep the Bluetooth device within 5 feet of the unit. * Move devices away from other electronics like Bluetooth devices, microwaves, and wireless routers. * Confirm the unit isn't paired with a previously connected device.
L
Laura RobertsonAug 19, 2025
Why Rockville RAM15BT V2 have poor mic sound?
- J
  jacobhawkinsAug 19, 2025
  To address poor microphone sound with your Rockville Speakers: 1. Ensure you are using the Mic In port. 2. If using wireless mics, check the batteries and volume settings, and ensure the antennas are fully extended.
T
Terry ClarkAug 22, 2025
How to eliminate buzzing sound from Rockville RAM15BT V2?
- K
  Kayla PattersonAug 22, 2025
  To address buzzing sounds from your Rockville Speakers: * Ensure you are using a proper cable. * For ¼? cables, there are 3 types: instrument, TS (unbalanced), and TRS (balanced). * Check the requirements of the connected gear and the input of the speaker and make sure you are using the appropriate cable.
J
john16Aug 26, 2025
How to improve bass on Rockville RAM15BT V2?
- N
  nleeAug 26, 2025
  To enhance bass on your Rockville Speakers, add a subwoofer to your setup, as PA speakers do not play deep frequencies as well. If you desire deep, thumping bass, adding a subwoofer is essential, regardless of brand or model.
P
Patrick NewmanAug 28, 2025
What to do if Rockville RAM15BT V2 Speakers have no sound or distorted sound?
- S
  Sean BaxterAug 29, 2025
  To troubleshoot no sound or distorted sound issues with your Rockville Speakers: * Check that all cables are correctly plugged in. * Verify the volume settings. * Ensure your microphone is on. * If using a mixing console, set the fader and balance to the center positions and increase the levels.
J
Jimmy FrederickSep 1, 2025
How to troubleshoot no power on Rockville RAM15BT V2?
- M
  Mr. Michael HaleSep 1, 2025
  If your Rockville Speakers have no power: 1. Ensure the unit is plugged in and the power switch is in the ON position. 2. Check that the power cable is securely connected to the unit. 3. Inspect and replace the fuse if needed.
A
Andrew BrownSep 4, 2025
Why TWS pairing fails on Rockville Speakers?
- A
  allenblackSep 4, 2025
  To resolve TWS pairing issues with your Rockville Speakers: * Ensure that both devices are turned on. * Make sure both devices are in Bluetooth mode. * Ensure both RAM-BT units are near each other. * Make sure that the unit is not paired to a previously paired device. * If TWS pairing is successful, but Bluetooth pairing to the main unit fails, please look at the "Bluetooth pairing fails" section above.
A
Angela StephensSep 7, 2025
How to stop mic feedback on Rockville RAM15BT V2 Speakers?
- R
  robert39Sep 7, 2025
  To eliminate mic feedback from your Rockville Speakers, try the following: * Point the microphones away from the speakers. * Ensure the microphones are positioned behind the speakers, not in front of them.
M
Melissa MartinezSep 12, 2025
What to do if Rockville Speakers have no SD or USB playback?
- B
  Brianna GutierrezSep 12, 2025
  To troubleshoot SD or USB playback issues with your Rockville Speakers: * Ensure you are in USB/SD mode. * Verify the SD card or USB drive is properly connected. * Make sure that the audio files are in the specified format. * Ensure the SD card/USB drive is not damaged.

Rockville RAM15BT V2 Specifications

General

Type	Active PA Speaker
Woofer Size	15 inches
Bluetooth	Yes
Outputs	XLR
USB Input	Yes
SD Card Input	Yes
Built-in Amplifier	Yes
Maximum SPL	120 dB
Impedance	8 Ohms
Frequency Response	20Hz - 20KHz
Inputs	RCA, Bluetooth
Microphone Input	Yes
Voltage	110V
Tweeter Size	1" inch