Need help?Do you have a question about the Rohde & Schwarz FSP40 and is the answer not in the manual?
General| Brand | Rohde & Schwarz |
|---|---|
| Model | FSP40 |
| Category | Measuring Instruments |
| Language | English |
Provides essential safety guidelines and precautions for operating the instrument.
Outlines basic safety instructions for operating and handling the product.
The main section detailing the performance testing procedures.
Procedure to check the accuracy of the reference frequency.
Procedure to test the instrument's immunity to interference.
Procedure to measure the 1st IF image frequency rejection.
Procedure to measure the 2nd IF image frequency rejection.
Procedure to measure the 3rd IF image frequency rejection.
Procedure to measure the 1st IF rejection.
Procedure to measure the 2nd IF rejection.
Procedure to check for nonlinearities in the instrument's performance.
Measurement of the Third Order Intercept Point (TOI).
Procedure to check the performance of the IF filters.
Procedure to verify the accuracy of bandwidth switching level.
Procedure to check the accuracy of the instrument's level measurements.
Procedure to measure the bandwidth of the instrument.
Procedure to determine the shape factor of the instrument's filters.
Procedure to check and display the instrument's noise characteristics.
Procedure to check level accuracy and frequency response.
Procedure to measure the instrument's frequency response.
Steps to determine level accuracy at 128 MHz with preamplifier.
Instructions for replacing various modules within the instrument.
Introduction to module replacement and spare parts.
Procedure for replacing the front module controller.
Procedure for replacing the lithium battery on the front module controller.
Procedure for replacing the hard disk.
Procedure for replacing the LCD and DC/AC converter.
Procedure for replacing the keyboard membrane or mat.
Procedure for replacing the front module labelling panel.
Procedure for replacing the floppy disk drive.
Procedure for replacing the power supply unit.
Procedure for replacing the instrument fan.
Procedure for replacing the RF input connector.
Procedure for replacing the motherboard.
Procedure for replacing the RF attenuator module.
Procedure for replacing Key/Probe and Vol./Phone boards.
Procedure for replacing the RF frontend module.
Procedure for replacing the detector board.
Procedure for replacing the IF filter board.
Procedure for replacing the MW converter unit.
Procedure for replacing the 8 GHz diplexer.
Procedure for replacing the 8 GHz YIG unit.
Procedure for replacing RF Extension 13/30.
Procedure for replacing RF Extension 40.
Procedure for replacing the AF Demodulator.
Procedure for replacing the OCXO module.
Procedure for replacing the Trigger module.
Procedure for replacing the Tracking Generator module.
Procedure for replacing the External Generator Control board.
Procedure for replacing the Wideband Calibrator.
Procedure for replacing the LAN adapter.
Procedure for replacing the Compact Flash Board.
Procedure for replacing the flash disk.
Procedure for replacing the external mixer board.
Procedure for replacing the electronic attenuator.
Procedure for replacing the DC/DC converter.
Procedure for replacing the battery charger module.
Procedure for replacing the instrument batteries.
General information on troubleshooting and recommendations.
Guidance for resolving issues when the R&S FSP cannot be switched on.
Procedure to check for short circuits in operating voltages.
Guidance for resolving issues during the instrument boot process.
Troubleshooting steps for errors when loading module EEPROM data.
Using the selftest feature to identify instrument errors.
Checks for operating voltages and error conditions.
Details voltage checks for the power supply.
Checks for regulated voltages on detector and IF filter boards.
Procedure for temperature measurement on the IF filter.
Procedure to check the 4-fold D/A converter on the detector board.
Testing reference signals on frontend and IF filter modules.
Checking the 128 MHz input level for FATAL ERROR.
Troubleshooting calibration signal level errors.
Troubleshooting control voltage errors for calibration signal.
Overview of the signal path testing sequence.
Troubleshooting signal path continuity through the RF attenuator.
Testing signal paths on the IF filter board.
Checking input level for IF filter and calibration amplifiers.
Testing LC and XTAL filters using Detector B.
Testing step gain of the IF amplifier using Detector C.
Diagnosing common errors related to Frontend 1.
Troubleshooting for missing signals or incorrect frequency display.
Diagnosing common errors related to MW converters.
Troubleshooting low or missing signal levels on MW converters.
Troubleshooting level conditions related to the diplexer.
To Next Page