Roland CPM-120 User Manual

m@ PANEL DESCRIPTIONS
«Control Paneb
a A a a A a a a a
CHANNEL 1 CHANNEL 2 CHANNEL 3 CHANNEL 4 CHANNEL 5 CHANNEL 6 CHANNEL 7 CHANNEL 8 —_
1 —
@ OVERLOAD INDICATOR oO ss)
OVERLOAD OVERLOAD
@ GAIN
© TREBLE
@ BASS
© EFFECT SEND VOLUME
@ PANPOT
@ CHANNEL VOLUME
@ OVERLOAD INDICATOR
The Overload Indicator will light when
the signal fed into the CPM reaches the
point which is 6dB lower than the clip
level.
@ GAIN
The Gain control is a continuously variable
rotary control that is to be used for
“trimming” the input signal level.
© TREBLE
@ BASS
These are used to boost or cut the portion
of the corresponding spectrum. At “<>”
position, a flat characteristic can be
obtained.
© EFFECT SEND VOLUME
The position of this continuously variable
rotary control determines the amount of
the signal sent from the Effect Send Jack
to the connected unit.
«Rear Panel
@ EFFECT SEND JACK
@ EFFECT RETURN JACK —
@ POWER SWITCH
@ LINE OUT JACK
@MODE SWITCH
@® SPEAKER TERMINAL (STEREO)
@SPEAKER JACK (STEREO)
@ INPUT JACK
This jack is to connect a musical instru-
ment, microphone, etc.
@ EFFECT SEND JACK
Through this jack, signal is sent to the
effect unit.
@ EFFECT RETURN JACK
Through this jack, the signal processed
by the effect unit (effect sound) can be
returned to the CPM.
@ LINE OUT JACK
To this jack, connect other powered
amplifier, tape recorder etc, and the
mixed sound will be sent out.
@ POWER SWITCH
Be sure to turn the Power Switch on or
off with the Master Volume set to low.
A, k 2,
iy
> + S&S G 7 8 Roland
oO COMPACT 7OMIEEED NADCEA
Picea aan Reisen aha oO ae OVERLOAD CRM-l20
‘@
© LEVEL INDICATOR
. 6 * 3 e z
Ei ee es ot Se et z°
q : z 9 Z
Ae ERS ee Seo)
pa Se ear Bind 3a a bee be. 7.
er
(e:'@1@:re
¢ . ¢ ‘ .
ACTER ee Ce)
_ ie iewe Sens Sete Bees ro.
* The pickup point of the Effect Send
signal is post channel volume.
@ PANPOT
The Panpot Control routs the signal sent
from the Input Jack to the left and/or
right mixing buses. By means of the
Panpot Control, input signal can be sent
exclusively to one mixing bus, or the
other, to both mixing buses equally, or
since the Panpot Control is continuously
variable to both mixing buses in any
relative proportion desired.
@ CHANNEL VOLUME
This knob controls the volume of each
channel independently.
© LEVEL INDICATOR
The Level Indicator detects the level of
the output signal. When “OdB” lights,
the signal of +4dBm is being sent
through the Output Jack, making the
@ PRE OUT JACK
@ MAIN IN JACK
These jacks can be used to connect a
graphic equalizer to eliminate feedback
and/or to achieve acoustical compatibility
with different performance locations.
* The Pre Out Jack can also be used to
set up another power amplifier, and the
Main In Jack can be used when the CPM-
120 is used as a power amplifier for
other unit.
* When the CPM-120 is used as BTL
amplifier, R does not work, but the Pre
Out Jack L sends out “L+R" signal.
© POWER INDICATOR
@ EFFECT RETURN VOLUME
@ HEADPHONES VOLUME
@ HEADPHONES JACK
@ MASTER VOLUME
RIGHT ———MAS TER VOLUME
rated output of the power amplifier
“60W/40"
© POWER INDICATOR
@ EFFECT RETURN VOLUME
This knob controls the volume of the
effect sound. Rotating the knob
clockwise will increase the volume.
@ HEADPHONES VOLUME
As you rotate this knob clockwise, the
headphones volume will increase. This
knob allows separate level setting free
from the Master Volume.
@ HEADPHONES JACK ‘
This is to connect headphones.
@ MASTER VOLUME
These are two independent controls
which control the volume of the left and
right channels, thus acting as an overall
volume controls for the CPM.
@ INPUT JACK
@ PREOUT JACK
@ MAIN IN JACK
@ SPEAKER JACK (MONO)
@ MODE SWITCH
Using this Mode Switch, the power
amplifier section of the CPM-120 can be
changed from Stereo to Mono (BTL), or
Mono to Stereo.
@ SPEAKER JACK
@ SPEAKER TERMINAL
Use either of these to connect a speaker.
* To use the CPM-120 as BTL(Monaural),
connect the speaker to the MONO (BTL)
of the Speaker Jack.
* When both the Speaker Jack and the
Terminal are simultaneously used, the
Speaker Jack has priority, so there is not
output from the Speaker Terminal.

Roland CPM-120 Specifications

General

Brand	Roland
Model	CPM-120
Category	Music Mixer
Language	English