Roland CPM-120 User Manual

@
CONNECTIONS
|
MICROPHONE
a ==] | KEYBOARD
o=% HHA Co GUITAR
TAPE RECORDER
SDE-3000 etc.
DIGITAL DELAY
TAPE
RECORDER
EFFECT
RIGHT LEFT RETURN SEND
© O
CAUTION : ro acouce tHe Asx oF €LECTRIC SHOCK - + SFEAKED mone ee nme OME
DO NOY REMOVE COVER NO USER SERVICEABLE PARTS INSIDE RE!
ATTENTION west Oo GO wm: O o = NOTES
eee cece ono 11 uo
ere arene Stl =H If the speaker of less than the specified im-
6.3A/125V .
FAUTION ro coviexorcctn a pedance is connected to th
Cnn REPLACE ONLY WITH oO O [R] [R} ; : t e Speaker Jack or
ATTENTION wn usm ne stl eames te Speaker Terminal of this unit, or the Termi-
ri eariosoe ic aes
nals are short-circuited, the protection
FUSIBLE OF MEME TYPE | |
circuit
will
effectively
work,
therefore,
no
sound
is
heard
from
the
speaker.
If
this
happends,
turn
the
unit
off,
correct
the
connection,
then
turn
it
on
again.
When the Pre Out or the Main In Jacks are
used with the Mode Switch set to MONO,
) ALAAAAAARAARIAAABAIAAAAAAQAD eal the R channel does not function. The L channel
of Pre Out Jacks, however, sends the mixed
signal of L and R.
oo
D
=)
°
O°
SEQ-315
STEREO
=
GRAPHIC
Even
though
both
types
of
speaker
outputs;
SRS-80L
SRS-80R
SRS-120
QUALIZER
Jacks
and
Terminal
are
provided,
the
terminal
SPEAKER
SYSTEM
SPEAKER
SYSTEM
SPEAKER
SYSTEM
does
not
function
when
_the
jack
is
being
used. Also, when both[L] and [R] jacks are
used, the Mono Out sends out no signal
(The one has the priority to the following one
like: Stereo L, R Jacks — Mono Jack >
@
OPERATION
Stereo
L,
R
Terminals.)
Set the Treble and If the Overload Indicator or
" the Level Indicator +3dB or
+6dB lights, the sound is dis-
torted, so you need to reduce
the channel volumes, the
Gains or the Master Volume
Controls.
For
usual
mixing
‘Bass
to
appropriate
levels.
]. After setting up the
" CPM-120, set each Gain
Control to LINE. Then
set each Channel Volume
to zero.
Set the relevant Effect
"Send Volume Controls to
appropriate positions.
Alf you wish to Alf you wish to Alf you wish to
; hear sound only hear sound from hear sound only
_Push the Power Switch, from the Left the both Chan- _from the Right
and make sure that the Channel, set the nels, set the Pan- Channel, set the
Power Indicator lights up. Panpot control pot to the centre Panpot Control : Set each Effect Return
pi to the L position. position. to the R position. er a ‘Volume Controls to an
: appropriate position.
/ Set each Channel Volumes
* to an appropriate position.
(Set the volume of the
channel not in use to zero.
3
Rae
_
oO
3 Turn the external devices (Such as an amplifier)
on.
3
-
1
?
Repeat
procedure
9.
4 Set the Gain Control to an appropriate level.
When using headphones
| 8 1 3 Connect stereo headphones to the
: - Headphones Jack, then set the
Set the L and R Master P Headphones Volume
Volumes
to
appropriate
ee
to
an
appropriate
positions.
4
2
}
position.
ALINE=+4dBm AINST= Electric AMIC= Microphone
Output equipment, Guitar, Electronic
etc. Keyboard, etc.

Roland CPM-120 Specifications

General

Brand	Roland
Model	CPM-120
Category	Music Mixer
Language	English