Roland FANTOM-06 Reference Manual

179179
Error Message List
If an incorrect operation is performed, or if processing could not be performed as you specied, an error message appears.
Refer to the explanation for the error message that appears, and take the appropriate action.
Message Meaning Action
USB Memory Not
Ready!
The USB ash drive is not inserted, or is inserted
incompletely.
Turn o the power, insert the USB ash drive correctly, and then
turn the power on again (p. 25).
The USB ash drive was removed after you selected data
that was on the USB ash drive.
The format of the USB ash drive is invalid. Use the FANTOM to format the USB ash drive (p. 159).
Storage Full! There is insucient space in the writing-destination. Delete unneeded data.
Incorrect File!
The format of the le being imported is invalid or
unsupported.
Use a le format that the FANTOM supports.
Audio les (WAV/AIFF/MP3) are supported (p. 97).
This le cannot be installed because it is an EXPANSION for a
dierent model.
The sound le that you are attempting to install is damaged.
–
Not Found! Empty
PAD was not
found.
During AUTO IMPORT of samples, there were not enough
empty pads for the samples being imported.
Use the sample DELETE function (p. 101) to prepare a sucient
number of empty pads, and then try the operation again.
Sample Too Long! The allowable sampling time has been exceeded. –
Sample Length Too
Short!
The sample is too short, and cannot be edited correctly.
If the sample is extremely short, editing may not produce the
desired result.
Storage Protected!
Since the USB ash drive’s lock setting is on, writing or
deletion is not possible.
Turn o the power, disconnect the USB ash drive, and turn o its
lock setting.
Storage Error!
There is a problem with the storage that is the target of the
operation.
If the target storage is in
¹ A USB ash drive: Use the FANTOM to format the USB ash
drive (p. 159).
¹ INTERNAL STORAGE: Execute the INTERNAL STORAGE
INITIALIZE operation (p. 158).
¹ Sample memory: Execute the sample DELETE ALL operation
(p. 101).
In other cases, execute a factory reset (p. 160).
If this does not solve the problem, contact your dealer or
customer support.
Incorrect Path!
When using File Utility, the Copy/Move destination path is
invalid.
A subfolder that includes the Copy/Move source cannot be
specied as the Copy/Move destination.
Invalid File/Folder
Name!
The le or folder name includes characters that cannot be
handled by the FANTOM.
The FANTOM cannot handle les or folders whose name includes
the following characters.
Nor can it handle special characters such as double-byte
characters.
Do not use these characters.
Invalid Char! Unusable characters are included.
Characters that cannot be handled by the FANTOM are shown in
the error message.
Do not use these characters.
Pattern End!
You have exceeded the maximum measures that can be
realtime-recorded.
–
Sequencer Error! A sequencer-related error has occurred.
Turn the power o and then on again before you proceed
(p. 25).
Data Full!
Since the maximum number of notes that can be stored in a
pattern has been exceeded, no further recording or editing
is possible.
Use the pattern utility modify commands Delete or Erase to delete
unneeded data from the pattern that you’re recording or editing
(p. 123).
Pattern status is
dierent!
When recording a layer consisting of multiple zones, the
recording-destination includes multiple tracks of diering
pattern status.
If you are layer-recording tracks, make sure that the loop settings
(loop length, playback position, LOOP SW setting) for the patterns
of those tracks are consistent with each other (p. 112).
Now Recording!
Since the FANTOM is recording, this operation cannot be
executed.
Stop recording before you execute the operation.
Now Playing!
Since the FANTOM is playing, this operation cannot be
executed.
Stop playback before you execute the operation.
Program Version
Error!
The FANTOM cannot start up.
The program cannot be loaded correctly. Alternatively, the
system update program might be incorrect.
Using the correct program, perform the update once again.
If this does not solve the problem, contact your dealer or
customer support.
MIDI Buer Full!
An unusually large amount of MIDI data was received, and
could not be processed.
Reduce the amount of MIDI messages that are being transmitted.
MIDI Oine! The MIDI IN connection was broken.
Check that there is no problem with the MIDI cable connected
to the FANTOM’s MIDI IN, and that the MIDI cable was not
disconnected.

Roland FANTOM-06 Specifications

General

Bit rate	24 bit
Pitch wheel	Yes
Product type	Digital synthesizer
Product color	Black
Sound effects	Chorus, Reverberation
Sound effects quantity	16
Chorus effects quantity	9
Keyboard number of keys	61
Preset programs quantity	10
Maximum polyphony (notes)	8
Reverberation effects quantity	7
6.35 mm (1⁄4-inch) input	1
Display type	LED
Power source type	AC

Weight and Dimensions

Depth	323 mm
Width	1006 mm
Height	95 mm
Weight	6000 g