179
Adding Effects
Adding Effects
MFX Type (Multi-Effects Type)
Use this parameter to select from among the 77 (Fantom-S88; 78)
available multi-effects. For details on multi-effects parameters, refer
to
“Multi-Effects Parameters”
(Parameter List).
Value:
0 (Through)–77 (Fantom-S88; 78)
MFX Output Level
(Multi-Effects Output Level)
Adjusts the volume of the sound that has passed through the multi-effects.
Value:
0–127
MFX Chorus Send Level
(Multi-Effects Chorus Send Level)
Adjusts the amount of chorus for the sound that passes through
multi-effects. If you don’t want to add the Chorus effect, set it to “0.”
Value:
0–127
MFX Reverb Send Level
(Multi-Effects Reverb Send Level)
Adjusts the amount of reverb for the sound that passes through
multi-effects. If you don’t want to add the Reverb effect, set it to “0.”
Value:
0–127
MFX Output Assign
(Multi-Effects Output Assign)
Adjusts the output destination of the sound that has passed through
the multi-effects.
Value
A:
Output to the OUTPUT A (MIX) jacks in stereo.
B:
Output to the OUTPUT B jacks in stereo.
If the Mix/Parallel parameter is set to “MIX,” all sounds are
output from the OUTPUT A (MIX) jacks in stereo (p. 193).
For some settings of MFX Structure, the sound that passes
through the multi-effect will be sent to a different multi-effect,
and the MFX Output Assign setting will be ignored.
Chorus Type
Selects either chorus or delay.
Value
0 (Off):
Neither chorus or delay is used.
1 (Chorus):
Chorus is used.
2 (Delay):
Delay is used.
3 (GM2 Chorus):
General MIDI 2 chorus
Chorus Output Select
Specifies how the sound routed through chorus will be output.
Value
MAIN:
Output to the OUTPUT jacks in stereo.
REV:
Output to reverb in mono.
M+R:
Output to the OUTPUT jacks in stereo, and to reverb in mono.
When set to “MAIN” or “M+R,” the OUTPUT jack from which
the sound is output is set in Chorus Output Assign ( ).
Chorus Level
Adjusts the volume of the sound that has passed through chorus.
Value:
0–127
Chorus Output Assign
Selects the pair of OUTPUT jacks to which the chorus sound is
routed when Chorus Output Select ( ) is set to “MAIN” or “M+R.”
Value
A:
Output to the OUTPUT A (MIX) jacks in stereo.
B:
Output to the OUTPUT B jacks in stereo.
When Chorus Output Select ( ) is set to “REV,” this setting
will have no effect.
If the Mix/Parallel parameter is set to “MIX,” all sounds are
output from the OUTPUT A (MIX) jacks in stereo (p. 193).
Reverb Type
Selects the type of reverb.
Value
0 (Off):
Reverb is not used.
1 (Reverb):
Normal reverb
2 (SRV Room):
This reverb simulates typical room acoustic
reflections.
3 (SRV Hall):
This reverb simulates typical concert hall acoustic
reflections.
4 (SRV Plate):
This reverb simulates a reverb plate, a popular
type of artificial reverb unit that derives its sound
from the vibration of a metallic plate. You can also
achieve unusual metallic-sounding reverbs using
“SRV Plate.”
5 (GM2 Reverb):
General MIDI 2 reverb
Reverb Level
Adjusts the volume of the sound that has passed through reverb.
Value:
0–127
Reverb Output Assign
Specifies how the sound routed through reverb will be output.
Value
A:
Output to the OUTPUT A (MIX) jacks in stereo.
B:
Output to the OUTPUT B jacks in stereo.
MFX-1–3 Source (Multi-Effects 1 Source)
●
When a performance is selected
Selects the multi-effects parameter settings that will be used by the
performance. If you wish to use the performance settings, select
“PRF.” If you wish to use the settings of the patch/rhythm set
7
8
9
10
11
12
13
15
13
13
Reference_e.book 179 ページ ２００３年７月１４日 月曜日 午後３時２５分
To Next Page
Loading...
