Roland FP-1

Keyboard
Maximum Polyphony
Tones
Specifications
88 Keys (hammer-action mechanism)
28 Voices
Piano 1, Piano 2, E.Piano, Strings, Syn Strings and Duals
(cf. Piano 1 + Piano 2 = Honky-Tonk)
Effects Chorus (5 types), Reverb (5 types)
Control Volume Slider, Tune Knob
Key Touch Control Light, Medium, Heavy or Full
Key Transpose -6 to 5 (semitone steps)
Rated Power Output 10Wx2 (BTL 4Q load)
Connectors Speaker Output Jacks (L, R), Line Out Jacks (mono / stereo)
Line In Jacks (mono / stereo), Headphone Jack (stereo)
Pedal Jacks (damper, soft / sostenuto / expression)
MID! Connectors (IN, OUT)
Power Supply AC117V, AC230V, or AC240 V
Power Consumption 45 W (AC117 V), 28 W (AC230 V), 28 W (AC240 V)
Dimensions Piano (FP-1): 1336 (W) x 350 (D) x 135 (H) mm
52-5/8 (W) x 13-3/4 (D) x 5-5/16 (H) inches
Stand (FPS-1): 1226 (W) x 476 (D) x 629 (H) mm
49-13/16 (W) x 18-3/4 (D) x 24-3/4 (H) inches
Total : 1336 (W) x 476 (D) x 754 (H) mm
52-5/8 (W) x 18-3/4 (D) x 29-11/16 (H) inches
Weight Piano (FP-1): 22.2kg / 48 lbs, 15 oz
Stand (FPS-1): 12.1 kg / 26 lbs, 11 0z
Total : 34.3 kg / 75 ibs, 10 oz
Accessories
Owner's
Manual,
Power
Cord,
Pedal
Switch
:
DP-6
Options Stand ; two speakers included (16 cm x 2): FPS-1
Stereo Headphone : RH-20 / 80 / 120
Pedal Switch : DP-2/6, BOSS FS-5U
Expression Pedal : EV-5
Connecting Cable : PU-1M/2/3
MIDI/SYNC Cable : MSC-07 / 15/25 /50/ 100
* In the interest of product development, the specifications and/or appearance of this unit are subject to change without prior notice.
Troubleshooting
No sound is heard.
* Is the [VOLUME] slider set to [MIN]?
¢ Are headphones connected to the PHONES jack?
* Is the piano set to LOCAL OFF? If so, press [FUNCTION] (so the indicator lights), then press [LOCAL] (be sure its
indicator also lights).
Soft effect is not properly obtained by depressing the pedal.
* Is the Pedal function set to Sostenuto or Expression? If so, press [FUNCTION] (so the indicator lights), then press
either [SOSTENUTO] or [EXPRESSION] (so both indicators are dark).
Some sounds are not heard when “Expression” is selected as the Pedal Function.
* Is the supplied DP-6 pedal connected? When the DP-6 is connected to the [SOFT PEDAL] jack, the STRINGS and SYN
STRINGS may not sound if the Expression function is selected.
The pitch of notes played is too high (or too low).
* Has a Transposition setting been made? If so, press [FUNCTION] (so the indicator lights), then press [#] and [b] simul-
taneously.
The piano is not in tune with other instruments or sound generators.
* Turn the [TUNE] knob on the FP-1’s rear panel to adjust the tuning. (See page 7.)
The sound from the speakers is distorted or is suddenly reduced.
¢ Are the speakers of the proper type and impedance? The speakers you connect should be 4 2 minimum. If improper
speakers are used, sound distortion or a volume decrease could result (in order to protect the internal circuitry).