Roland fp-30 - Page 34

MIDI Implementation
34
70202: Overdrive0Delay
This eect connects an overdrive and a delay in series.
No Parameter Value Description
1
Overdrive
Drive #1
0–127 0 –127
Degree of distortion
Also changes the volume.
2
Overdrive
Pan
0–127 L64–63R
Stereo location of the
overdrive sound
3 Delay Mode 0–1 ms, note
When this is set to “note,” the
eect is synchronized with
the tempo.
4 Delay Time 0–127 1–2540 ms
Adjusts the delay time from
the direct sound until the
delay sound is heard. (ms)
5 Delay Time 0–21 note
Adjusts the delay time from
the direct sound until the
delay sound is heard. (note)
6
Delay
Feedback
49–89 0–+80 %
Adjusts the proportion of the
delay sound that is fed back
into the eect.
7
Delay HF
Damp
0–17
200–8000
Hz, Bypass
Adjusts the frequency above
which sound fed back to the
eect will be cut. If you do not
want to cut the high
frequencies, set this
parameter to Bypass.
8
Delay
Balance #2
0–100
D100:0W–
D0:100W
Adjusts the volume balance
between the sound that is
sent through the delay (W)
and the sound that is not sent
through the delay (D).
9 Level 0–127 0–127 Output Level
70203: Distortion0Chorus
The parameters are essentially the same as in “Overdrive0Chorus,” with the
exception of the following two.
Overdrive Drive0Distortion Drive
Overdrive Pan0Distortion Pan
70204: Distortion0Flanger
The parameters are essentially the same as in “Overdrive0Flanger,” with the
exception of the following two.
Overdrive Drive0Distortion Drive
Overdrive Pan0Distortion Pan
70205: Distortion0Delay
The parameters are essentially the same as in “Overdrive0Delay,” with the
exception of the following two.
Overdrive Drive0Distortion Drive
Overdrive Pan0Distortion Pan
70206: Enhancer0Chorus
This eect connects an enhancer and a chorus in series.
No Parameter Value Description
1
Enhancer
Sens
0–127 0 –127 Sensitivity of the enhancer
2 Enhancer Mix 0–127 0 –127
Level of the overtones
generated by the enhancer
3
Chorus Pre
Delay
0–125 0.0–100.0 ms
Adjusts the delay time from
the direct sound until the
chorus sound is heard.
4
Chorus Rate
Mode
0–1 Hz, note
When this is set to “note,” the
eect is synchronized with
the tempo.
5
Chorus Rate
#1
1–127
0.05–10.00
Hz
Frequency of modulation (Hz)
6 Chorus Rate 0–21 note
Frequency of modulation
(note)
No Parameter Value Description
7
Chorus Depth 0–127 0 –127 Depth of modulation
8
Chorus
Balance #2
0–100
D100:0W–
D0:100W
Adjusts the volume balance
between the sound that is
sent through the chorus (W)
and the sound that is not sent
through the chorus (D).
9 Level 0–127 0–127 Output Level
70207: Enhancer0Flanger
This eect connects an enhancer and a anger in series.
No Parameter Value Description
1
Enhancer
Sens
0–127 0 –127 Sensitivity of the enhancer
2 Enhancer Mix 0–127 0 –127
Level of the overtones
generated by the enhancer
3
Flanger Pre
Delay
0–125 0.0–100.0 ms
Adjusts the delay time from
when the direct sound begins
until the anger sound is
heard.
4
Flanger Rate
Mode
0–1 Hz, note
When this is set to “note,” the
eect is synchronized with
the tempo.
5
Flanger Rate
#1
1–127
0.05–10.00
Hz
Frequency of modulation (Hz)
6 Flanger Rate 0–21 note
Frequency of modulation
(note)
7
Flanger
Depth
0–127 0 –127 Depth of modulation
8
Flanger
Feedback
0–98 -98–+98 %
Adjusts the proportion of the
anger sound that is fed back
into the eect. Negative (-)
settings will invert the phase.
9
Flanger
Balance #2
0–100
D100:0W–
D0:100W
Adjusts the volume balance
between the sound that is
sent through the anger (W)
and the sound that is not sent
through the anger (D).
10 Level 0–127 0–127 Output Level