Roland HandSonic HPD-20 - Page 9

MIDI Implementation
9
 Sound Controller 10 (Controller Number 79)
Status 2nd byte 3rd byte
BnH 4FH vvH
n = MIDI channel number: 0H–FH (ch.1–ch.16)
vv = control value 00H–7FH (0–127)
* When D-BEAM CC# (MENU --> SYS --> MIDI --> MIDI) setting is “SOUND10 (79) ,” this
is transmitted when D-BEAM is used.
* When Realtime Modify Pitch CC# (MENU --> SYS --> MIDI --> MIDI) setting is
“SOUND10 (79) ,” this is transmitted when Realtime Modify (PITCH) is adjusted.
* When Realtime Modify Eect CC# (MENU --> SYS --> MIDI --> MIDI) setting is
“SOUND10 (79) ,” this is transmitted when Realtime Modify (EFFECT) is adjusted.
 General Purpose Controller 5 (Controller Number 80)
Status 2nd byte 3rd byte
BnH 50H vvH
n = MIDI channel number: 0H–FH (ch.1–ch.16)
vv = control value 00H–7FH (0–63: OFF, 64–127: ON)
* This is transmitted when the [EFFECT] button is pressed.
 General Purpose Controller 6 (Controller Number 81)
Status 2nd byte 3rd byte
BnH 51H vvH
n = MIDI channel number: 0H–FH (ch.1–ch.16)
vv = control value 00H–7FH (0–127)
* When D-BEAM CC# (MENU --> SYS --> MIDI --> MIDI) setting is “GENERAL6 (81) ,” this
is transmitted when D-BEAM is used.
* When Realtime Modify Pitch CC# (MENU --> SYS --> MIDI --> MIDI) setting is
“GENERAL6 (81) ,” this is transmitted when Realtime Modify (PITCH) is adjusted.
* When Realtime Modify Eect CC# (MENU --> SYS --> MIDI --> MIDI) setting is
“GENERAL6 (81) ,” this is transmitted when Realtime Modify (EFFECT) is adjusted.
 General Purpose Controller 7 (Controller Number 82)
Status 2nd byte 3rd byte
BnH 52H vvH
n = MIDI channel number: 0H–FH (ch.1–ch.16)
vv = control value 00H–7FH (0–127)
* When D-BEAM CC# (MENU --> SYS --> MIDI --> MIDI) setting is “GENERAL7 (82) ,” this
is transmitted when D-BEAM is used.
* When Realtime Modify Pitch CC# (MENU --> SYS --> MIDI --> MIDI) setting is
“GENERAL7 (82) ,” this is transmitted when Realtime Modify (PITCH) is adjusted.
* When Realtime Modify Eect CC# (MENU --> SYS --> MIDI --> MIDI) setting is
“GENERAL7 (82) ,” this is transmitted when Realtime Modify (EFFECT) is adjusted.
 General Purpose Controller 8 (Controller Number 83)
Status 2nd byte 3rd byte
BnH 53H vvH
n = MIDI channel number: 0H–FH (ch.1–ch.16)
vv = control value 00H–7FH (0–127)
* When D-BEAM CC# (MENU --> SYS --> MIDI --> MIDI) setting is “GENERAL8 (83) ,” this
is transmitted when D-BEAM is used.
* When Realtime Modify Pitch CC# (MENU --> SYS --> MIDI --> MIDI) setting is
“GENERAL8 (83) ,” this is transmitted when Realtime Modify (PITCH) is adjusted.
* When Realtime Modify Eect CC# (MENU --> SYS --> MIDI --> MIDI) setting is
“GENERAL8 (83) ,” this is transmitted when Realtime Modify (EFFECT) is adjusted.
Program Change
Status 2nd byte
CnH ppH
n = MIDI channel number: 0H–FH (ch.1–ch.16)
pp = program number: 00H–7FH (prog.1–prog.128)
* When a kit is selected, the corresponding program number is transmitted.
* Not transmitted when Program Change Tx (MENU --> SYS --> MIDI --> MIDI) is set
to “OFF.”
Pitch Bend Change
Status 2nd byte 3rd byte
EnH llH mmH
n = MIDI channel number: 0H–FH (ch.1–ch.16)
mm, ll = pitch bend value: 00 00H–40 00H–7F 7FH
(-8192–0–+8191)
* When Realtime Modify Pitch CC# (MENU --> SYS --> MIDI --> MIDI) setting is “PITCH
BEND,” this is transmitted when Realtime Modify (PITCH) is adjusted.