Roland HandSonic HPD-20 - Turning the Power On;Off

MIDI Implementation
10
 Channel Mode Messages
* The following channel mode messages are transmitted on the channel specied as
the MIDI Channel (MENU --> SYS --> MIDI --> MIDI).
All Sound O (Controller Number 120)
Status 2nd byte 3rd byte
BnH 78H 00H
n = MIDI channel number: 0H–FH (ch.1–ch.16)
* This is transmitted when the ALL SOUND OFF ( [SHIFT] + [EXIT] ) is used.
Reset All Controller (Controller Number 121)
Status 2nd byte 3rd byte
BnH 79H 00H
n = MIDI channel number: 0H–FH (ch.1–ch.16)
* This is transmitted when the Factory Reset (MENU --> SYS --> Factory Reset) is
executed.
 System Realtime Messages
Active Sensing
Status
FEH
* This message is transmitted at intervals of approximately 250 msec.
 System Exclusive Messages
Identity Reply, V-LINK message, and MIDI Visual Control message are the only System
Exclusive messages transmitted by this device.
Universal Non-Realtime System Exclusive Messages
 Identity Reply Message
Status Data byte Status
F0H 7EH, dev, 06H, 02H, 41H, F7H
78H, 02H, 00H, 00H, 00H,
01H, 00H, 00H
Byte Explanation
F0H Exclusive Status
7EH ID number (Universal Non-Realtime Message)
dev Device ID (10H xed)
06H Sub ID#1 (General Information)
02H Sub ID#2 (Identity Request)
41H ID Number (Roland)
78H 02H Device Family Cord
00H 00H Device Family Number Code
00H 01H 00H 00H Software Revision Level
F7H EOX (End Of Exclusive)
* When Identity Request is received, Identity Reply message will be transmitted.
V-LINK Messages
 V-LINK ON
Transmitted when entering V-LINK mode.
Status Data byte Status
F0H 41H, 10H, 00H, 51H, 12H, F7H
10H, 00H, 00H, 01H, nnH,
10H, 02H, sum
Byte Explanation
F0H Exclusive Status
41H ID Number (Roland)
10H Device ID (10H xed)
00H Model ID#1 (V-LINK)
51H Model ID#2 (V-LINK)
12H Command ID (DT1)
10H 00H 00H Address
01H Data (V-LINK ON)
nnH Data (Clip Control Rx MIDI Ch.
(00H-0FH (ch.1-ch.16) ) Initial Value = 0FH (ch.16) )
10H Data (Color Control Rx MIDI Ch. (OFF) )
02H Data (Note Message Enabled (Assignable) )
sum Check Sum
F7H EOX (End Of Exclusive)
* The unit will enter V-LINK mode if Control Mode (MENU --> SYS --> MIDI --> VISUAL)
is set to “V-LINK” and MIDI Visual Control (MENU --> SYS --> MIDI --> VISUAL) is
turned “ON.”
* MIDI Channel (MENU --> SYS --> MIDI --> VISUAL) setting is used as the Clip Control
Rx MIDI Ch.
* Only the Clip Control Rx MIDI Ch address (10H 00H 01H) and data are transmitted
when the MIDI Channel setting is made in V-LINK mode.
 V-LINK OFF
Transmitted when exiting V-LINK mode.
Status Data byte Status
F0H 41H, 10H, 00H, 51H, 12H, F7H
10H, 00H, 00H, 00H, 70H,
Byte Explanation
F0H Exclusive Status
41H ID Number (Roland)
10H Device ID (10H xed)
00H Model ID#1 (V-LINK)
51H Model ID#2 (V-LINK)
12H Command ID (DT1)
10H 00H 00H Address
00H Data (V-LINK OFF)
70H Check Sum
F7H EOX (End Of Exclusive)
* The unit will exit V-LINK mode if the MIDI Visual Control (MENU --> SYS --> MIDI -->
VISUAL) is turned “OFF” or if the Control Mode (MENU --> SYS --> MIDI --> VISUAL)
is set to “MVC.”