Roland JUNO-D - Page 73

73
Adding effects
Effects
13: SPACE-D
Space-D is a multiple chorus that applies two-phase modulation in
stereo. It gives no impression of modulation, but produces a
transparent chorus effect.
fig.MFX-13
14: St CHORUS (Stereo Chorus)
This is a stereo chorus. A filter is provided so that you can adjust the
timbre of the chorus sound.
fig.MFX-14
15: St FLANGER (Stereo Flanger)
This is a stereo flanger. It produces a metallic resonance that rises
and falls like a jet airplane taking off or landing. A filter is provided
so that you can adjust the timbre of the flanged sound.
fig.MFX-15
Parameter
Value Description
Pre Delay
0.0–100 [ms] Adjusts the time delay from
when the direct sound begins
until the processed sound is
heard.
Rate # 0.05–10.00 [Hz] Adjusts the rate of modulation.
Depth 0–127 Adjusts the depth of modula-
tion.
Phase 0–180 [deg] Adjusts the spatial spread of the
sound.
Low Gain -15– +15 [dB] Adjusts the gain of the low fre-
quency.
High Gain -15– +15 [dB] Adjusts the gain of the high fre-
quency.
Balance # D100:0W–
D0:100W
Adjusts the volume balance be-
tween the direct sound and the
chorus sound.
With a setting of D100:0W only the
direct sound will be output, and
with a setting of D0:100W only the
chorus sound will be output.
Level 0–127 Adjusts the output level.
Parameter
Value Description
Filter Type
OFF, LPF, HPF Selects the type of filter.
OFF: A filter will not be used.
LPF: Cuts the frequency range
above the cutoff frequency.
HPF: Cuts the frequency range
below the cutoff frequency.
Cutoff Freq 200–8000 [Hz] Adjusts the basic frequency of
the filter.
Pre Delay 0.0–100 [ms] Adjusts the time delay from
when the direct sound begins
until the processed sound is
heard.
Rate # 0.05–10.00 [Hz] Adjusts the rate of modulation.
L in
R in
Space-D
Space-D
L out
R out
2-Band
EQ
2-Band
EQ
Balance W
Balance W
Balance D
Balance D
L in
R in
Chorus
Chorus
L out
R out
2-Band
EQ
2-Band
EQ
Balance W
Balance W
Balance D
Balance D
Depth
0–127 Adjusts the depth of modula-
tion.
Phase 0–180 [deg] Adjusts the spatial spread of the
sound.
Low Gain -15– +15 [dB] Adjusts the gain of the low fre-
quency.
High Gain -15– +15 [dB] Adjusts the gain of the high fre-
quency.
Balance # D100:0W–
D0:100W
Adjusts the volume balance be-
tween the direct sound and the
chorus sound.
With a setting of D100:0W only the
direct sound will be output, and
with a setting of D0:100W only the
chorus sound will be output.
Level 0–127 Adjusts the output level.
Parameter
Value Description
Filter Type
OFF, LPF, HPF Selects the type of filter.
OFF: A filter will not be used.
LPF: Cuts the frequency range
above the cutoff frequency.
HPF: Cuts the frequency range
below the cutoff frequency.
Cutoff Freq 200–8000 [Hz] Adjusts the basic frequency of
the filter.
Pre Delay 0.0–100 [ms] Adjusts the time delay from
when the direct sound begins
until the flanger sound is heard.
Rate # 0.05–10.00 [Hz] Adjusts the rate of modulation.
Depth 0–127 Adjusts the depth of modula-
tion.
Phase 0–180 [deg] Adjusts the spatial spread of the
sound.
Feedback # -98– +98 [%] Adjusts the amount (%) of the
processed sound that is returned
(fed back) into the input. Posi-
tive (+) settings will return the
sound in phase, and negative (-)
settings will return the sound in
reverse phase.
Low Gain -15– +15 [dB] Adjusts the gain of the low fre-
quency.
High Gain -15– +15 [dB] Adjusts the gain of the high fre-
quency.
Parameter
Value Description
R in
R out
L in
L out
Flanger
Feedback
Feedback
Flanger
Balance W
Balance D
Balance W
Balance D
2-Band
EQ
2-Band
EQ
JUNO-D_e.book 73 ページ ２００４年６月１１日 金曜日 午後１時２１分