Roland JUNO-D - Page 75

75
Adding effects
Effects
18: LONG DELAY
This is useful when you want to apply a delay that is longer than 17:
St DELAY.
fig.MFX-18
19: MOD DELAY (Modulation Delay)
This effect adds modulation to the delayed sound, producing an
effect similar to a flanger.
When Feedback Mode is NORMAL:
fig.MFX-19a
When Feedback Mode is CROSS:
fig.MFX-19b
HF Damp
200–8000 [Hz],
BYPASS
Adjusts the frequency above
which sound fed back to the ef-
fect will be cut.
If you do not want to cut the
high frequencies of the feed-
back, set this parameter to BY-
PASS.
Low Gain -15– +15 [dB] Adjusts the gain of the low fre-
quency.
High Gain -15– +15 [dB] Adjusts the gain of the high fre-
quency.
Balance # D100:0W–
D0:100W
Adjusts the volume balance be-
tween the direct sound and the
delay sound.
With a setting of D100:0W only the
direct sound will be output, and
with a setting of D0:100W only the
delay sound will be output.
Level 0–127 Adjusts the output level.
Parameter
Value Description
Delay
0–840 [ms], note
*1
Adjusts the time from the direct
sound until the delay sound is
heard.
Feedback # -98– +98 [%] Adjusts the proportion (%) of
the delay sound that is fed back
into the effect.
Negative (-) settings will invert
the phase.
HF Damp 200–8000 [Hz],
BYPASS
Adjusts the frequency above
which sound fed back to the ef-
fect will be cut.
If you do not want to cut the
high frequencies of the feed-
back, set this parameter to BY-
PASS.
Low Gain -15– +15 [dB] Adjusts the gain of the low fre-
quency.
High Gain -15– +15 [dB] Adjusts the gain of the high fre-
quency.
Balance # D100:0W–
D0:100W
Adjusts the volume balance be-
tween the direct sound and the
delay sound.
With a setting of D100:0W only the
direct sound will be output, and
with a setting of D0:100W only the
delay sound will be output.
Level 0–127 Adjusts the output level.
Parameter
Value Description
Feedback
Balance W
Balance W
L in
R in
L out
R out
Delay
Balance D
Balance D
2-Band
EQ
2-Band
EQ
Parameter
Value Description
Feedback Mode
NORMAL,
CROSS
Selects the way in which delay
sound is fed back into the effect.
NORMAL: The left delay sound
will be fed back into the left de-
lay, and the right delay sound
into the right delay.
CROSS: The left delay sound
will be fed back into the right de-
lay, and the right delay sound
into the left delay.
Delay Left 0–370 [ms] Adjusts the time from the direct
sound until when the left delay
sound is heard.
Delay Right 0–370 [ms] Adjusts the time from the direct
sound until when the right delay
sound is heard.
Feedback -98– +98 [%] Adjusts the proportion (%) of
the delay sound that is fed back
into the effect.
Negative (-) settings will invert
the phase.
HF Damp 200–8000 [Hz],
BYPASS
Adjusts the frequency above
which sound fed back to the ef-
fect will be cut.
If you do not want to cut the
high frequencies of the feed-
back, set this parameter to BY-
PASS.
Rate # 0.05–10.00 [Hz] Adjusts the speed of the modu-
lation.
Depth 0–127 Adjusts the depth of the modu-
lation.
Phase 0–180 [deg] Adjusts the spatial spread of the
sound.
R in R out
L in L out
Feedback
Feedback
Balance W
Balance D
Balance W
Balance D
2-Band
EQ
2-Band
EQ
Delay
Delay
Modulation
Modulation
R in
R out
L in
L out
Feedback
Feedback
Balance W
Balance D
Balance W
Balance D
2-Band
EQ
2-Band
EQ
Delay
Delay
Modulation
Modulation
JUNO-D_e.book 75 ページ ２００４年６月１１日 金曜日 午後１時２１分