To Next PageTo Next Page
How to stop my Roland Synthesizer from turning off by itself?
If the power on your Roland Synthesizer turns off by itself, set the system setting “Auto Power Off” to “OFF” if you want the power to remain on constantly.
What to do if my Roland JUNO-Gi power won't turn on?
If your Roland Synthesizer isn't turning on, here are a few things you can check: 1. Make sure that the included AC adapter and power cord are correctly connected. Using any AC adapter or power cord other than the supplied items can cause malfunctions. 2. Check the remaining battery power. 3. Open the battery case and make sure that the batteries are installed in the correct polarity.
How to fix sound distortion on Roland JUNO-Gi Synthesizer?
If you're experiencing sound distortion with your Roland Synthesizer, here's what you can do: * If a specific Live Set or Layer sounds distorted, try lowering the volume of that Live Set or Layer. * If the overall sound is distorted, lower the [VOLUME] knob. * Check the system setting “SOUND” to ensure the Output Gain isn't raised excessively.
Why is the pitch wrong on my Roland JUNO-Gi Synthesizer?
If the pitch of your Roland Synthesizer sounds wrong, here are a few things to check: * Verify the system setting “Master Tune”. * Check the pedal and the pitch bender, as the pitch could have been changed by a pedal operation or by a pitch bend message received from an external MIDI device. * Check the settings of the Coarse and Fine parameters, as you may have edited the coarse tune or fine tune settings of a specific Layer.
Why is there no sound from a specific track on my Roland JUNO-Gi?
If you're not getting any sound from a specific track on your Roland Synthesizer, try raising the volume level (Track Level parameter). Also, ensure that the V-track setting has selected the correct V-track that contains data.
Why can’t I play arpeggios on my Roland JUNO-Gi Synthesizer?
If you can’t play arpeggios on your Roland Synthesizer, and “USB Song Sync Mode” is set to “SLAVE,” the device must be receiving MIDI clock from an external device. Set “USB Song Sync Mode” to “MASTER” unless you’re synchronizing the JUNO-Gi with an external device.
Why is the sound from USB Audio strange on my Roland Synthesizer?
If you're experiencing strange sound from USB Audio on your Roland Synthesizer, switch off Center Cancel.
Why are not all the tracks of an SMF format 1 file being played on my Roland JUNO-Gi?
If your Roland Synthesizer is not playing all the tracks of an SMF format 1 file, reduce the number of tracks.
Why is the effect not applied on my Roland Synthesizer?
If the effect is not being applied on your Roland Synthesizer, check the on/off setting of each effect. Also, ensure each layer’s Output Assign is set to “MFX.” Finally, check the send level to each effect, as the effect won’t be obtained if the send level to that effect is set at 0. Even if the send levels to the effect is set above 0, the effect won’t be applied if the multi-effect output level, chorus level, or reverb level are set to 0. Check each of these settings.
Why does the display backlight turn off by itself on my Roland Synthesizer?
If the display backlight on your Roland Synthesizer turns off by itself, set the system setting “Power Save Mode” to “OFF” if you want the backlight to remain on constantly.
General| Polyphony | 128 voices |
|---|---|
| Parts | 16 parts |
| Keyboard | 61 keys (with velocity) |
| Wave Memory | 128 MB (16-bit linear equivalent) |
| D Beam Controller | Yes |
| Power Supply | AC Adaptor |
| Effects | Multi-effects, reverb, chorus |
| Display | 240 x 64 dots graphic LCD |
| Sequencer | 16-track sequencer |
| Outputs | 2 x 1/4" (L/Mono, R), 1 x 1/4" (phones) |
| USB | USB (audio/MIDI/data transfer) |
| Preset Patches | Over 1, 300 |
| External Storage | SD/SDHC memory card |
| Connectors | MIDI In/Out, USB |
| Weight | 5.7 kg |
| Patches | Preset: 1, 000 + User: 256 |
| Sampling | Not supported |
