37
Effects editing parameters
29: GATE
Cuts the output level according to the volume of the sound sent into
the effect. Use this when you want to create an artificial-sounding
decrease in the reverb’s decay.
fig.MFX29
30: LOFI NOISE (Lo-Fi Noise)
In addition to a lo-fi effect, this adds various types of noise such as
white noise and disc noise.
fig.MFX30
31: LOFI COMPRESS (Lo-Fi Compress)
This is an effect that intentionally degrades the sound quality for
creative purposes.
fig.MFX31
Parameter
Value Description
Threshold
#1
0–127 Volume level at which the gate be-
gins to close
Mode GATE,
DUCK
Type of gate
GATE:
The gate will close when
the volume of the original sound
decreases, cutting the original
sound.
DUCK (Ducking):
The gate will
close when the volume of the
original sound increases, cutting
the original sound.
Balance #2 D100:0W–
D0:100W
Volume balance between the direct
sound (D) and the effect sound (W)
Attack
Time
0–127 Adjusts the time it takes for the gate
to fully open after being triggered.
Hold Time 0–127 Adjusts the time it takes for the gate
to start closing after the source
sound falls beneath the Threshold.
Release
Time
0–127 Adjusts the time it takes for the gate
to fully close after the hold time.
Level 0–127 Output level
Parameter
Value Description
LoFi Type
1–9 Degrades the sound quality. The
sound quality grows poorer as this
value is increased.
Post Filter
Type
OFF, LPF,
HPF
Selects the type of filter applied to
the sound after it passes through
the Lo-Fi effect.
OFF:
no filter is used
LPF:
cuts the frequency range
above the Cutoff
HPF:
cuts the frequency range
below the Cutoff
Post Filter
Cutoff
200–8000
Hz
Cutoff frequency of the Post Filter
W/P Noise
Type
WHITE,
PINK
Switch between white noise and
pink noise.
L in
R in
L out
R out
Gate
Gate
R in
R out
L in
L out
Lo-Fi
Lo-Fi
Noise Gen.
W/P Noise
LPF
200–8000
Hz, BY-
PASS
Cutoff frequency of the low pass fil-
ter applied to the white/pink noise
(BYPASS: no cut)
W/P Noise
Level
0–127 Volume of the white/pink noise
Disc Noise
Type
LP, EP, SP,
RND
Type of record noise
The frequency at which the noise
is heard depends on the selected
type.
Disc Noise
LPF
200–8000
Hz, BY-
PASS
Adjusts the cutoff frequency of the
low pass filter applied to the record
noise. If you don’t want to filter out
any high frequencies, set this pa-
rameter to BYPASS.
Disc Noise
Level
0–127 Volume of the record noise
Hum Noise
Type
50Hz, 60Hz Frequency of the hum noise
Hum Noise
LPF
200–8000
Hz, BY-
PASS
Cutoff frequency of the low pass fil-
ter applied to the hum noise (BY-
PASS: no cut)
Hum Noise
Level
0–127 Volume of the hum noise
Balance #1 D100:0W–
D0:100W
Volume balance between the direct
sound (D) and the effect sound (W)
Level #2 0–127 Output level
Parameter
Value Description
Pre Filter
Type
1–6 Selects the type of filter applied to
the sound before it passes through
the Lo-Fi effect.
LoFi Type 1–9 Degrades the sound quality. The
sound quality grows poorer as this
value is increased.
Post Filter
Type
OFF, LPF,
HPF
Selects the type of filter applied to
the sound after it passes through
the Lo-Fi effect.
OFF:
no filter is used
LPF:
cuts the frequency range
above the Cutoff
HPF:
cuts the frequency range
below the Cutoff
Post Filter
Cutoff
200–
8000 Hz
Cutoff frequency of the Post Filter
Balance #1 D100:0W–
D0:100W
Volume balance between the direct
sound (D) and the effect sound (W)
Level #2 0–127 Output level
Parameter
Value Description
L in
R in
L out
R out
Compressor
Lo-Fi
Lo-Fi
Compressor
MC-808_Slist_e.book 37 ページ ２００７年９月７日 金曜日 午前１１時１１分
To Next Page
Loading...
Need help?
General
