60
Rhythm editing parameters
These TVA (Time Variant Amplifier) parameters specify how the volume and pan of the sound will change.
These parameters specify the depth of the amp envelope (change in volume over time) and the shape of the envelope itself.
Amp
Parameter
Value Description
Tone Level
(Rhythm Tone Level)
0–127 Volume of each Rhythm Tone
This parameter is used mainly to adjust the volume balance between Rhythm Tones.
Wave Level 0–127 Volume of each wave
This parameter is used mainly to adjust the volume balance between waves.
Tone Pan
(Rhythm Tone Pan)
L64–63R Pan of each Rhythm Tone
L64 is far left, 0 is center, and 63R is far right.
Random Pan Depth 0–63 Amount by which the pan will be varied randomly each time you press a pad
Increasing this value will produce a greater amount of random change.
Alternate Pan Depth L63–63R Amount by which the pan will be moved alternately between left and right each time you press a pad
Increasing this value will produce a greater amount of change. This value can be adjusted in the L or
R direction, and these will invert the order in which the tone is panned to left and right. If you want
two tones to alternate between left and right, set each tone to opposite L and R values.
Wave Pan L64–63R Pan of each wave
L64 is far left, 0 is center, and 63R is far right.
Wave Rnd Pan Sw
(Wave Random Pan
Switch)
OFF, ON Use this setting to cause the waveform’s panning to change randomly each time a pad is pressed (ON)
or not (OFF).
The range of the panning change is set by the Random Pan Depth setting.
Wave Alt Pan Sw
(Wave Alternate Pan
Switch)
OFF, ON,
REVS
Set this to ON to pan the Wave according to the Alternate Pan Depth settings, or to REVS when you
want the panning reversed.
If you do not want the panning to change each time a pad is pressed, set this to OFF.
Amp Env (Amp Envelope)
Parameter
Value Description
A-Env V-Curve
(Amp Envelope
Velocity Curve)
FIX, 1–7 Curve by which velocity will affect the volume of the tone
If this is “FIX,” the volume of the tone will stay the same regardless of how the velocity varies.
A-Env V-Sens
(Amp Envelope
Velocity Sensitivity)
-63– +63 Amount by which velocity will affect the volume of the tone
Set a positive (+) value if you want to increase the tone’s volume change, or a negative (-) value if you
want to decrease the tone’s volume change.
A-Env T1 V-Sens
(Amp Envelope
Time 1 Velocity
Sensitivity)
-63– +63 Amount by which velocity will affect T1 (time) of the Amp envelope
Specify a positive (+) value if you want the T1 time to speed up, or a negative (-) value if you want it
to slow down.
A-Env T4 V-Sens
(Amp Envelope
Time 4 Velocity
Sensitivity)
-63– +63 Amount by which T4 (time) of the Amp envelope will change in response to the key-off velocity
Specify a positive (+) value if you want the T4 time to speed up, or a negative (-) value if you want it
to slow down.
A-Env Time1–4
(Amp Envelope
Time 1–4)
0–127 Amp envelope times (T1–T4)
Higher settings of these values will lengthen the time over which the next volume level of the enve-
lope is reached. (For example, T2 is the time over which the level changes from L1 to L2.)
A-Env Level1–3
(Amp Envelope
Level 1–3)
0–127 Amp envelope levels (L1–L3)
Specifies the change in volume at each point, relative to the reference level.
T1 T2 T3 T4
L3
L1
L2
Level
key is pressed
key is released
Time
1234567
MC-808_Slist_e.book 60 ページ ２００７年９月７日 金曜日 午前１１時１１分
To Next Page
Loading...
