Roland MV-8800 - Page 68

MIDI Implementation
A-68
MV-8800 Appendices
■ Channel Voice Messages
● Note off
n = MIDI channel number: 0H - FH (ch.1 - 16)
kk = note number: 15H - 74H (21 - 116)
vv = note off velocity: 00H - 7FH (0 - 127)
● Note on
n = MIDI channel number: 0H - FH (ch.1 - 16)
kk = note number: 15H - 74H (21 - 116)
vv = note on velocity: 01H - 7FH (1 - 127)
● Polyphonic Key Pressure
n = MIDI channel number: 0H - FH (ch.1 - 16)
kk = note number: 15H - 74H (21 - 116)
vv = Polyphonic Key Pressure: 00H - 7FH (0 - 127)
● Control Change
* By selecting a controller number that corresponds to the setting of parameters of
controllers (Assignable sliders), the MV-8800 can transmit any control change message.
❍ Hold 1 (Controller number 64)
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127) 0-63 = OFF, 64-127 = ON
* Transmitted when the Foot Switch Assign parameter (PANEL screen) is set to Damper.
● Channel Pressure
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Channel Pressure: 00H - 7FH (0 - 127)
■ System Realtime Messages
● Active Sensing
* This message is transmitted at intervals of approximately 250 msec.
* This message is not sent when the Tx Active Sensing parameter (MIDI screen) is Off.
3.1 Messages recorded during recording
■ Channel Voice Messages
● Note Off
n=MIDI channel number:0H - FH (ch.1 - ch.16)
kk=note number: 00H - 7FH (0 - 127)
vv=note off velocity: 00H - 7FH (0 - 127)
* Not received when the Note parameter (RECORDING FILTER popup) is Off.
● Note on
n=MIDI channel number:0H - FH (ch.1 - ch.16)
kk=note number: 00H - 7FH (0 - 127)
vv=note on velocity: 01H - 7FH (1 - 127)
* Not received when the Note parameter (RECORDING FILTER popup) is Off.
● Polyphonic Key Pressure
n=MIDI channel number:0H - FH (ch.1 - ch.16)
kk=note number: 00H - 7FH (0 - 127)
vv=Polyphonic Aftertouch:00H - 7FH (0 - 127)
* Not received when the Poly Aftertouch parameter (RECORDING FILTER popup) is Off.
● Control Change
n=MIDI channel number:0H - FH (ch.1 - ch.16)
kk=Control number: 00H - 78H (0 - 120)
vv=value: 00H - 7FH (0 - 127)
* Not received when the Control Change parameter (RECORDING FILTER popup) is Off.
● Program Change
n=MIDI channel number:0H - FH (ch.1 - ch.16)
pp=Program number:00H - 7FH (prog.1 - prog.128)
* Not received when the Program Change parameter (RECORDING FILTER popup) is Off.
● Channel Pressure
n=MIDI channel number:0H - FH (ch.1 - ch.16)
vv=Channel Aftertouch:00H - 7FH (0 - 127)
* Not received when the Channel Aftertouch parameter (RECORDING FILTER popup) is
OFF.
● Pitch Bend Change
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
ll, mm=Pitch Bend value: 00, 00H - 00, 40H - 7F, 7FH (-8192 - 0 - +8191)
* Not received when the Pitch Bend parameter (RECORDING FILTER popup) is Off.
2.Data Transmission
(Sound Generator section)
Status
2nd byte 3rd byte
8nH
kkH vvH
Status
2nd byte 3rd byte
9nH kkH vvH
Status
2nd byte 3rd byte
AnH
kkH vvH
Status
2nd byte 3rd byte
BnH
40H vvH
Status
2nd byte
DnH
vvH
Status
FEH
3.Receive Data (Sequencer Section)
Status
2nd byte 3rd byte
8nH kkH vvH
9nH kkH 00H
Status
2nd byte 3rd byte
9nH
kkH vvH
Status
2nd byte 3rd byte
AnH
kkH vvH
Status
2nd byte 3rd byte
BnH kkH vvH
Status
2nd byte
CnH
ppH
Status
2nd byte
DnH
vvH
Status
2nd byte 3rd byte
EnH llH mmH
MV-8800_a_e.book 68 ページ ２００６年１１月１０日 金曜日 午前１０時１９分