Roland MV-8800 - Page 72

MIDI Implementation
A-72
MV-8800 Appendices
■ System Realtime Messages
● Timing Clock
* Sent when the SYNC Mode parameter (SYNC or PATTERN SYNC screen) is set to
Slave-MIDI or Remote.
● Start
* Sent when the SYNC Mode parameter (SYNC or PATTERN SYNC screen) is set to
Slave-MIDI or Remote.
● Continue
* Sent when the SYNC Mode parameter (SYNC or PATTERN SYNC screen) is set to
Slave-MIDI or Remote.
● Stop
* Sent when the SYNC Mode parameter (SYNC or PATTERN SYNC screen) is set to
Slave-MIDI or Remote.
■ System Exclusive Message
● MIDI Time code
Byte
Remarks
F0H Exclusive status
7FH Universal System Exclusive Realtime Header
7FH Device ID
01H sub-ID #1 (MIDI Time code)
01H sub-ID #2 (Full Message)
hrH hours and type: 0 yy zzzzz
yy type:
00 = 24 Flame/sec
01 = 25 Flame/sec
10 = 30 Flame/sec
11 = 30 Flame/sec
zzzzz: Hours (00 - 23)
mnH Minutes (00 - 59)
scH Seconds (00 - 59)
frH Frames (00 - 29)
F7H EOX (End of Exclusive)
* Sent when the MTC Output parameter (SYNC or PATTERN SYNC screen) is set to On.
● MIDI Machine Control (MMC)
* Sent when the MMC Output parameter (SYNC or PATTERN SYNC screen) is set to On.
❍ STOP (MCS)
Byte
Remarks
F0H Exclusive status
7FH Universal System Exclusive Realtime Header
7FH Device ID
06H MMC command message
01H STOP (MCS)
F7H EOX (End of Exclusive)
❍ DEFFERRED PLAY (MCS)
Byte
Remarks
F0H Exclusive status
7FH Universal System Exclusive Realtime Header
7FH Device ID
06H MMC command message
03H DEFERRED PLAY (MCS)
F7H EOX (End of Exclusive)
❍ RECORD STROBE
Byte Description
F0H Exclusive status
7FH Universal System Exclusive Realtime Header
7FH Device ID
06H MMC Command Message
06H RECORD STROBE
F7H EOX (End of System Exclusive message)
❍ RECORD EXIT
Byte
Description
F0H Exclusive status
7FH Universal System Exclusive Realtime Header
7FH Device ID
06H MMC Command Message
07H RECORD EXIT
F7H EOX (End of System Exclusive message)
❍ LOCATE (MCP)
Format2—LOCATE [TARGET]
Byte
Remarks
F0H Exclusive status
7FH Universal System Exclusive Realtime Header
7FH Device ID
06H MMC command message
44H LOCATE (MCP)
06H Byte count
01H “TARGET” sub-Command
hrH Standard Time Specification with subframes (type ff)
mnH
scH
frH
ffH
F7H EOX (End of Exclusive)
Status
F8H
Status
FAH
Status
FBH
Status
FCH
Status
Data Byte Status
F0H
7FH, 7FH, 01H, 01H, hrH, mnH, scH, frH
F7H
Status
Data Byte Status
F0H
7FH, 7FH, 06H, 01H
F7H
Status
Data Byte Status
F0H
7FH, 7FH, 06H, 03H
F7H
Status
Data Byte Status
F0H
7FH, 7FH, 06H, 06H F7H
Status
Data Byte Status
F0H
7FH, 7FH, 06H, 07H F7H
Status
Data Byte Status
F0H
7FH, 7FH, 06H, 44H, 06H, 01H, hrH, mnH, scH, frH, ffH
F7H
MV-8800_a_e.book 72 ページ ２００６年１１月１０日 金曜日 午前１０時１９分