Roland TD-27 - Page 2

n = MIDI channel number: 0H–FH (ch.1–ch.16)
vv = Control value: 00H–7FH (0–127)
Pedal position: open to closed
Head strike position: center to perimeter
Rim strike position: deep to shallow
* In the channel to which the HI-HAT<BOW> is assigned, setting [SYSTEM]-[MIDI]-[CONTROL] HH Pedal CC to “EXPRESSION (11)” changes the
hi-hat control pedal position.
* The strike position of the pad corresponding to the same note channel's note number received changes immediately after
[SYSTEM]-[MIDI]-[CONTROL] Snare CC (for the SNARE pad head and rim), Ride CC (for the RIDE pad bow), or Toms/AUXs CC (for head and rim of
TOM 1–3, AUX 1–3 pads) is set to “EXPRESSION (11).”
○General Purpose Controller 1 (Controller number 16)
Status 2nd byte 3rd byte
BnH 10H vvH
n = MIDI channel number: 0H–FH (ch.1–ch.16)
vv = Control value: 00H–7FH (0–127)
Pedal position: open to closed
Head strike position: center to perimeter
Rim strike position: deep to shallow
* In the channel to which the HI-HAT<BOW> is assigned, setting [SYSTEM]-[MIDI]-[CONTROL] HH Pedal CC to “GENERAL1 (16)” changes the
hi-hat control pedal position.
* The strike position of the pad corresponding to the same note channel's note number received changes immediately after
[SYSTEM]-[MIDI]-[CONTROL] Snare CC (for the SNARE pad head and rim), Ride CC (for the RIDE pad bow), or Toms/AUXs CC (for head and rim of
TOM 1–3, AUX 1–3 pads) is set to “GENERAL1 (16).”
○General Purpose Controller 2 (Controller number 17)
Status 2nd byte 3rd byte
BnH 11H vvH
n = MIDI channel number: 0H–FH (ch.1–ch.16)
vv = Control value: 00H–7FH (0–127)
Pedal position: open to closed
Head strike position: center to perimeter
Rim strike position: deep to shallow
* In the channel to which the HI-HAT<BOW> is assigned, setting [SYSTEM]-[MIDI]-[CONTROL] HH Pedal CC to “GENERAL2 (17)” changes the
hi-hat control pedal position.
* The strike position of the pad corresponding to the same note channel's note number received changes immediately after
[SYSTEM]-[MIDI]-[CONTROL] Snare CC (for the SNARE pad head and rim), Ride CC (for the RIDE pad bow), or Toms/AUXs CC (for head and rim of
TOM 1–3, AUX 1–3 pads) is set to “GENERAL2 (17).”
○General Purpose Controller 3 (Controller number 18)
Status 2nd byte 3rd byte
BnH 12H vvH
n = MIDI channel number: 0H–FH (ch.1–ch.16)
vv = Control value: 00H–7FH (0–127)
Pedal position: open to closed
Head strike position: center to perimeter
Rim strike position: deep to shallow
* In the channel to which the HI-HAT<BOW> is assigned, setting [SYSTEM]-[MIDI]-[CONTROL] HH Pedal CC to “GENERAL3 (18)” changes the
hi-hat control pedal position.
* The strike position of the pad corresponding to the same note channel's note number received changes immediately after
[SYSTEM]-[MIDI]-[CONTROL] Snare CC (for the SNARE pad head and rim), Ride CC (for the RIDE pad bow), or Toms/AUXs CC (for head and rim of
TOM 1–3, AUX 1–3 pads) is set to “GENERAL3 (18).”
○General Purpose Controller 4 (Controller number 19)
Status 2nd byte 3rd byte
BnH 13H vvH
n = MIDI channel number: 0H–FH (ch.1–ch.16)
vv = Control value: 00H–7FH (0–127)
Pedal position: open to closed
Head strike position: center to perimeter
Rim strike position: deep to shallow
* In the channel to which the HI-HAT<BOW> is assigned, setting [SYSTEM]-[MIDI]-[CONTROL] HH Pedal CC to “GENERAL4 (19)” changes the
hi-hat control pedal position.
* The strike position of the pad corresponding to the same note channel's note number received changes immediately after
[SYSTEM]-[MIDI]-[CONTROL] Snare CC (for the SNARE pad head and rim), Ride CC (for the RIDE pad bow), or Toms/AUXs CC (for head and rim of
TOM 1–3, AUX 1–3 pads) is set to “GENERAL4 (19).”
○High Resolution Velocity Prefix (Controller number 88)
Status 2nd byte 3rd byte
BnH 58H kkH
n = MIDI channel number: 0H–FH (ch.1–ch.16)
kk = High resolution velocity prefix: 00H–40H (0–64)
* If a note-on message is received immediately thereafter on the same note channel, the force (velocity) of the pad strike is expressed as
follows according to the values of the note-on velocity and the high resolution velocity prefix.
* When the note-on velocity is less than 127 and the high resolution velocity prefix is less than 64
The velocity is the same as the note-on velocity.
* When the note-on velocity is less than 127 and the high resolution velocity prefix is 64
If we let the note-on velocity be “x,” the velocity is expressed as “x+0.5.”
* When the note-on velocity is 127
If we let the high resolution velocity prefix be “y,” the velocity is expressed as “127+(0.5*y).”
* Velocity values below the decimal point are not expressed in the screen of the TD-27. If we let the velocity be “x,” velocities above
127 are expressed as “127+(x-127).”
* If a note-off is received immediately thereafter on the same note channel, the high resolution velocity prefix is reset.
* Not received when [SYSTEM]-[MIDI]-[CONTROL] HI-Reso Velocity is set to “OFF.”
* If a message whose high resolution velocity prefix value of 65 or greater is received, it is received as a value of 64.
●Program Change
Status 2nd byte
CnH ppH
n = MIDI channel number: 0H–FH (ch.1–ch.16)