pp = Program number: 00H–63H (prog.1–prog.100)
* Not received when [SYSTEM]-[MIDI]-[BASIC] program Change Rx is set to “OFF.”
* Received only if the channel number matches the MIDI Channel of [SYSTEM]-[MIDI]-[BASIC].
* The sound will change beginning with the next Note-On after the Program Change is received. Voices which were already sounding before
the Program Change was received will not be affected.
■Channel Mode Messages
* The following Channel Voice Messages can be received in [KIT EDIT]-[OTHER]-[KIT MIDI]-[MIDI CH] MIDI CH.
* Not received when [SYSTEM]-[MIDI]-[BASIC] Tx/Rx Sw is set to “OFF.”
●All Sounds Off (Controller number 120)
Status 2nd byte 3rd byte
BnH 78H 00H
n = MIDI channel number: 0H–FH (ch.1–ch.16)
* When this message is received, all currently-sounding notes on the corresponding channel will be silenced. However, the status of
channel messages will not change.
●Reset All Controllers (Controller number 121)
Status 2nd byte 3rd byte
BnH 79H 00H
n = MIDI channel number: 0H–FH (ch.1–ch.16)
* When this message is received, polyphonic key pressure for all pads assigned to the same channel number is reset to 0.
* If the channel number is the same as the channel that is assigned for HI-HAT<BOW>, the controller that is assigned by
[SYSTEM]-[MIDI]-[CONTROL] HH Pedal CC is reset to 0.
●All Notes Off (Controller number 123)
Status 2nd byte 3rd byte
BnH 7BH 00H
n = MIDI channel number: 0H–FH (ch.1–ch.16)
* The same processing will be carried out as when All Sounds Off is received.
●OMNI OFF (Controller number 124)
Status 2nd byte 3rd byte
BnH 7CH 00H
n = MIDI channel number: 0H–FH (ch.1–ch.16)
* The same processing will be carried out as when All Sounds Off is received.
●OMNI ON (Controller number 125)
Status 2nd byte 3rd byte
BnH 7DH 00H
n = MIDI channel number: 0H–FH (ch.1–ch.16)
* The same processing will be carried out as when All Sounds Off is received.
●MONO (Controller number 126)
Status 2nd byte 3rd byte
BnH 7EH mmH
n = MIDI channel number: 0H–FH (ch.1–ch.16)
mm= mono number: 00H–10H (0–16)
* The same processing will be carried out as when All Sounds Off is received.
●POLY (Controller number 127)
Status 2nd byte 3rd byte
BnH 7FH 00H
n = MIDI channel number: 0H–FH (ch.1–ch.16)
* The same processing will be carried out as when All Sounds Off is received.
■System Realtime Message
●Timing Clock
Status
F8H
* Recognized only when the [SYSTEM]-[MIDI]-[SYNC] Sync Mode is set at “EXTERNAL.”
●Start
Status
FAH
* If a START message is received while the song is stopped, the click playback is reset. The song does not play.
* Recognized only when the [SYSTEM]-[MIDI]-[SYNC] Sync Mode is set at “EXTERNAL.”
●Active Sensing
Status
FEH
* When Active Sensing is received, the unit will begin monitoring the intervals of all further messages. While monitoring, if the interval
between messages exceeds about 500 ms, the same processing will be carried out as when All Sounds Off, All Notes Off and Reset All
Controllers are received, and message interval monitoring will be halted.
■System Exclusive Message
To Next Page
Loading...
