Roland TD-7 - Page 114

I Pitch Bend Change
\‘-I’-='|ten :1 Pitch Bend Cltttnge nie.~I.~;;I§_ge is reei-:i\-Iei.l. the pitch will tilt;tn;..;e.
I Attertouch
Al'tertottelIt is;t ltmetion t\'l1tL'lI ;Illo\\I:I\-"t.itI tottiter .~Iotmtl.s h ';t 1 tlt--‘int’ iIIe.s>tIzIetI>t|te kt-\I>Iol';t ket-Iltoitrtl
. w D . ¢
alter‘ the tttttes ltttre heen plztt-‘eel ,=\l'tt:rtot|tIlt ittcltttles two kinds til It1t‘.‘$.*i;.l§1L".‘$' polt--IplttInitI kex-I |t1It:.~;.
sends inl‘omIt;1tiotIt for the entire elmnnel.
The TD-'1’ sends pol}-Ipltonit: key pre.~t.sIt1tIe tltessiges trltezt the rim of Ll pad is held and t'ele;.I.~t_Ietl.
' l I'L‘
. . . . . '_ st
tttemattgesfi VI-'lItt‘lI send inlonnzttiott lot‘ t;'Llt.‘ll key pl;n-Ied, and eltztnnel key |1l'L‘fih'Lil'L‘ tttess;tges_ \\I|titIh
Wltett receiving polypltonie key pre.~;stI re l1It‘.H‘5;l_t{c’h' Iro|tI1e.\tten1;tl It-lll)l tle\Iitfes, the _Tl.)—'.? will re.~;pond
as il’ _\_-‘oh ’t\-’t;’l'L‘ holding the rim ol‘ 11. ptttl.
I Program Change
Generally’. Progt';tn1ClIt;inge Ittessttges are ttsetl for tIlt;IttgiItg sountls. I - l.28;tft'I.’\’11llLl l’ro_eII;I.i1i(IlII;t
I\iumhetIs.
The TD-7 ttllttws I-'ou to change l)1l{t.'l]L‘h' tising, l’rogI';tttI Cltztnge ttte-sstiges.
I Control Change
Control Cltztnge ntesetges control severttl |'ttntI'tion.s. sttelt as ntotlttlzttion. Piiti. etc. Funetion.I~I
speeil'ieI;l hy Control Ntttttlvers.
The TD3? st-Isteiti um send Hi-hut Control Petlztl inl'orm;ttion ttsing (._"Iontrol Clt:-Inge tttessztgcs.
The TI.)-'? can ttend Hold ittessitges \\-‘hen the FO(}[.5'Vt'llCl1 motle is set to mode Z. t_fi-it I’. I 2-ail
§ K
I1gt' 1":
E1111‘
I
How the Patch Numbers
in the TD-7 correspond
to Program Change
Numbersis explained on
page 70.
Chapter 6 System Setting 1 12
'*I—— ——II "* *" ——— 7 * *7 — — — ————— ——::—S S — — _—::_S—:S—:_<—~— — T _ S _ SS4» ~ SS_~_ SS S