Roland TD-7 - Page 129

@
l’rus.-" l'r-trrts.-witr."l1 .2. trod the 'l"l")-‘T is ru;rtl§' lot" rt'wrrlin§.: |turl‘r>rtt't;|rtt"c ir'tl'ontt;.ttior1. This is the
rt‘tfot'tl .\:t:1ntl-lit motlu. '
® l’l;t§-' tr purl to stztrt t'mtr‘tlitt_=.1. then |tl;rf.'tl1u pltrttse you \\'i.~<h tn t'emt'tl. \‘€-ilten you ltzn-‘e l"inisltet.l
pl;tt'io_<.;_ pt'u.s.s' lr l(ll.*1\\’llC]l .1 tr. t st: up t'ut‘r. >rt.lin 3.1. The t‘r.-‘tit trtlutl tlzttzt will he ittttnct.littl't;'l}-* ]'llLl§’l.7L] l7L1t.‘l\'.
®
l.’1‘cs.sitt_t.{ l'oot>;t\'itt‘l1 3tlur'irt_t:, pl:t§t'l1;tt'lt will .=2t;trt :'ccortlih§_1again. Yott can rct'ortl (Loop liccortl)
orcr the cxistint: tl;tt;r ;t.s t'n;tn\_-' titncs as 't't'ttl \\'i.~tl"t.
I.‘ » -
® l’rc.s.~tin_e, loot.~t\\-‘itrlt l \\-hilu :1 pltrztscisl1t'itt;_§pl:t§--‘ct! hatch {or t‘umt'tlctl) will stop |tl;tylr.tt'l< (or
r"<:ro1‘tlin;.1 1. t-'r;.t.-".in_s: the |"tt'e\'iottsl~_t' recot'tler;| plti";tse.
I Setting the Interval and Quantize
.-'\lit't‘ ;'~ilt.‘]'l :thn\'t.*. l~ttllu\\' tlttrs prr1t't‘t.lttt't_.':
(Q) l’|‘e.~;.s' [ENTER].
@ .\-lr_t\‘t* tl1et'trr-"ot'to the I t"!?L_-t:'E*t“'*-.-*-B \';.tlutr. then set the vztlttc with the [DATA] tliatl.
Pmmi QM m S we 5
I on no . all I.i MIG: ‘Ill. : E uni: ]
Inhenwale ififi
T
Value
Parameter P
@ .\-It )\'L' the cttr.-:ot' to It"ti'..-1:-?t""*-.-*-$1 . thtsn .~tt:-'let't1;?i..t-&l"'t‘l‘..- It XE‘ using the [DATA] dial.
III
3-.‘ I
Font PM M S H
Qoantiaza twee
“':- "-3
M‘:
III
w
t
® i\‘ln\’t‘ the rtttsor to the 5;il.t-E':tl'"t'iI.- i Zr:-"L-= vrtlttc{resolutiont.t|1t:nsettltt=\':2lt1e with the [DATA]
tlittl.
tl=
=f=
=l=
The Sound-on-Sound
function cannot record a
long phrase (refer to
page 126).
Pressing footswitch 1
(while the phrase is
stopped) will change the
Patch Number. Each
time you press footswitch
1 the Patch Number will
increase; twice quickly
will decrease the
number.
The Sound-on-Sound
and Phrase Sequencer
(P. 92) data are recorded
in the common memory
area. If the Phrase Se-
quencer data tstoo large.
the Sound-on-Sound
-S data cannot be recorded.
lf this hap-pens, check
the available memory
with the Available
Memory function (P. 105)
and reduce the amount
of data you want to
record.
127
Chapter 6 System Setting