Roland V-Mixer VM-3100 - Page 95

VM-3100 List of Algoriyhms
high-frequencies are damped. The reverb sound in the band
above the standard frequency is damped.
HiDampGain [HD-G] (High Damp Gain)
-36 - 0 dB
This parameter adjusts the amount of damping for High
Damp. No high-frequency damping occurs when set to “0.”
HiCutFreq [HiCut] (High Cut Frequency)
0.2 - 20.0 kHz
This parameter adjusts the frequency at which a low-pass
filter starts to be applied. The effect is applied to the reverb
sound.
07 STEREO DELAY CHORUS
This algorithm connects a stereo delay and a stereo chorus in
series, allowing you to add depth and spaciousness to the
sound while preserving the positioning of the stereo input
signal.
Stereo Delay Stereo Chorus EQ
oes Loy cho t EQ : ,
DELAY
This parameter creates a distinctive effect (such as a thicker
sound) by applying a delayed sound to the direct sound. By
using Tempo Delay, you can easily set the delay time to
match the tempo of the song.
Time L [TimeL]1 - 1200 msec
Time R [TimeR]1 - 1200 msec
This parameter adjusts the delay time (i.e., the interval for
which sound is delayed).
Feedback L [FB LJO - 100
Feedback R [FB R]O - 100
This parameter adjusts the amount of feedback. Changing
the amount of feedback causes the number of time the
delayed sound is repeated to change as well.
FX Level [EffLv]O - 100
This adjusts the volume of the delay sound.
Dry Level [DryLv]O - 100
Adjusts the volume of the direct sound.
HiCutFreq [HiCut] (High Cut Frequency)
0.2 - 20.0 kHz, THRU
The High Cut Filter cuts the frequency contents that are
higher than the set frequency. This parameter adjusts the
frequency where the high cut filter starts working. When it is
set to “THRU,” the high cut filter does not work at all.
HiDampGain [HD-G] (High Damp Gain)
-36 - 0 dB
This parameter adjusts the amount of damping for High
Damp. No high-frequency damping occurs when set to “0.”
CHORUS
These parameters are the same as those in the CHORUS in
Algorithm 05 (KEYBOARD MULTI) (p.16).
Mod.LR Phs [Phase]NORM, INV
Depth [Depth]O — 100
Rate [Rate] 0-100
FX Level [EffLv]O — 100
Dry Level [DryLvJO — 100
Pre Delay [{PreDL]0 — 50msec
LoCutFreq [LoCut] (Low Cut Frequency)THRU, 50 ~ 800 Hz
HiCutFregq [HiCut] (High Cut Frequency)0.5 - 12.5 kHz, THRU
EQ (3-Band Equalizer)
These parameters are the same as those in the EQ in
Algorithm 01 (REVERB & GATE) (p.10).
Low Type [LType]SHELV, PEAK
Low Freq [LFreq]20 — 2000 Hz
Low Gain [LGain]-12 - +12 dB
Low Q[LQ] 0.3 - 10.0
Mid Freq [MFreq]200 ~ 8000 Hz
Mid Gain [MGain]-12 — +12 dB
Mid Q [MQ] 0.3 - 10.0
High Type [HType]SHELV, PEAK
High Freq [HFreq]1.4 — 20.0 kHz
High Gain [HGain]-12 — +12 dB
High Q [HQ] 0.3 - 10.0
Out Level [OutLv]-60 — +12 dB
O8 STEREO PITCH SHIFTER
This algorithm features two pitch shifters arranged in
parallel, making it stereo compatible. It can shift the pitch of
the input signal up to one octave up or down. This algorithm
can be used with either the insert method or the send/return
method.
19