Need help?Do you have a question about the Roma GECCO and is the answer not in the manual?
Symbol for immediate danger to life and health.
Symbol for important tips and useful information.
Indicates optional components or steps.
Instructions for assembly, disassembly, repair, and maintenance personnel.
Only qualified personnel for electrical work.
Use in dry, non-explosive rooms; avoid aggressive atmospheres.
Danger from moving parts; keep people and animals away.
Proper assembly, handling, and use of original parts.
For opening/closing openings; no liability for other uses.
Building stability and suitable mounting materials are critical.
Closed, dry rooms, -20°C to +50°C.
Similar to assembly, requires qualified personnel.
Symbol for immediate danger to life and health.
Symbol for important tips and useful information.
Indicates optional components or steps.
Instructions must be read and understood by all personnel.
Only qualified personnel allowed for electrical work.
Assembly requires extensive training.
Use with appropriate covers and safety devices.
Adhere to accident prevention and standards like EN 12453.
Use necessary PPE when working.
Brief operator and hand over manuals.
Dry, non-explosive rooms, no aggressive atmospheres.
Risk of crushing/shearing; keep clear.
Disconnect power before working.
Do not clean drive/brackets wet.
Proper assembly, handling, and original parts are required.
For opening/closing; no liability for other purposes.
Damages from misuse void liability.
Only original ROMA parts; others void warranty.
Ensure building stability and use suitable mounting materials.
Closed, dry rooms, -20°C to +50°C.
Performed by qualified personnel.
Danger for life and health.
Dispose packaging for recycling.
Useful tips for handling.
For user errors or omissions.
Must be read, understood, and heeded by specialists.
Only electricians or authorized personnel.
Training required for installation/disassembly.
Motor covered by protective cap.
Consider accident prevention and EN12453.
Wear appropriate work attire.
User to be advised on operating conditions.
Transmit documentation to user.
Avoid humid or explosive environments.
Risk of crushing, pinching, shearing.
Enter only when fully open.
Cut power before electrical work.
Do not clean with water.
Requires proper assembly and functioning.
For closing openings; no liability for other uses.
For not following installation instructions.
Use only original ROMA parts.
Check stability before installation.
Check and adapt fixing material.
Install in closed, dry rooms, -20°C to +50°C.
Procedure similar to assembly; by qualified personnel.
Direct danger for life and health.
Sort materials for reuse.
Important tips for handling.
Manufacturer liability exclusion for user fault.
Optional.
Manual must be read, understood, and followed.
Only skilled persons for electrical installations.
Training in shutters or door construction required.
Operation only with safety devices.
Adhere to regulations like EN12453.
Wear protective equipment.
Operator must be informed of conditions.
Hand over manuals and conformity declaration.
Dry, non-explosive, not aggressive atmospheres.
Danger from moving parts; keep clear.
Enter only when fully open.
Switch off power before work.
Do not clean wet.
Claims require expert assembly and handling.
For openings; no liability for other uses.
Not following instructions voids warranty.
Use only original parts.
Check structural stability; system does not reinforce.
Check and adapt mounting material.
Closed, dry rooms, -20°C to +50°C.
Same procedure as assembly; by qualified personnel.
Note that hand-held transmitters are already adjusted/programmed.
Warning and instruction book symbols.
Loosen the screw slightly (approx. 1mm).
Tighten the screw.
Conduct a test run to check operation.
Verify the alignment of components.
Description of the terminal strip's position on the circuit board.
Shows wiring for signal lamp and terminal assignments.
Features the control board with DIP switches for configuration.
Performing a test run for the radio control.
Instructions for learning/programming the radio control.
Description of the illumination function.
Detailed steps for programming radio controls and settings.
Instructions for adjusting the spring tension if required.
Specifications for power, current, force, speed, and temperature.
Explanation of the functions for each DIP switch setting.
Procedure for learning transmitters and terminating learning.
How to erase single transmitters or channels.
How the housing push-button and radio channels work.
Learning and resetting force settings.
Specifications for power, current, force, speed, and temperature.
Explanation of functions for DIP switch settings.
Procedures for learning, terminating, and erasing transmitters.
Clearing the radio receiver and channel management.
Push-button, radio channels, and additional buttons.
Programming travel limits and force settings.
Specifications for voltage, current, power, force, speed, and temperature.
Explanation of DIP switch functions for door operation.
Programming, terminating, and erasing transmitters.
Clearing receiver and managing channels.
Operations via housing button and radio channels.
Setting travel limits and force curves.
Specifications for voltage, current, power, force, speed, and temperature.
Explanation of DIP switch functions for door operation.
Programming, terminating, and erasing transmitters.
Clearing the radio receiver and individual channels.
Using housing switch and radio channels.
Adjusting travel limits and force curves.
General| Brand | Roma |
|---|---|
| Model | GECCO |
| Category | Garage Door Opener |
| Language | English |
To Next Page
