GB
• Open the lid (9) of your vacuum cleaner – fig. 14.
• Open the motor protection grid (12) – fig. 17a.
• Remove the microfilter * (13) – fig. 17b.
• Discard the microfilter * (13) into a dustbin – fig. 17c and replace it with a new microfilter (ref. ZR0039 01).
• Place the pins in the notches – fig. 17d.
• Lock the microfilter * behind the engine protection grid (12) – fig. 17e.
• Make sure the microfilter* (13) is properly in position before closing the lid (9).
HEPA FILTER CASSETTE* (REF: ZR0041 01)
Important: Replace the HEPA filter cassette* ZR0041 01 every 6 months (depending on the frequency of use).
• Open the lid (9) of your vacuum cleaner – fig. 14.
• Remove the HEPA filter cassette* (14a) – fig. 18a – 18b.
• Throw the cassette into the dustbin – fig. 18c.
• Place the pins in the notches – fig. 18d.
• Lock the new HEPA filter cassette* (14a) (ref. ZR0041 01) in its housing – fig. 18e.
• Make sure the HEPA filter cassette* (14a) is properly in position before closing the lid (9).
CLEANING THE HEPA FILTER CASSETTE* (ref: ZR0042 01)
Please note! This cleaning operation is reserved exclusively for the HEPA filter cassette * ref: ZR0042 01.
• Open the lid (9) of your vacuum cleaner – fig. 14.
• Remove the HEPA filter cassette* (14b) – fig. 19a – 19b.
• Tap the HEPA filter cassette* (14b) over a dustbin – fig. 19c.
• Then hold it under running water – fig. 19d, and allow to dry at least 24 hours – fig 19e.
• Ensure that the HEPA filter cassette * (14b) is completely dry before replacing it.
• Place the pins in the notches – fig. 19f.
• Lock the HEPA filter cassette* (14b) (Ref: ZR0042 01) in its housing – fig. 19g.
• Make sure the HEPA filter cassette* (14b) is properly in position before closing the lid (9).
CLEANING THE VACUUM CLEANER
• Wipe the body of the vacuum cleaner and accessories with a soft damp cloth, then dry.
• Wipe the lid with a dry cloth – fig. 20.
• Do not use detergents or any corrosive or abrasive products.
6. TROUBLESHOOTING
Important: As soon as your vacuum cleaner stops performing efficiently, and before making any checks,
stop it by pressing on the On/Off pedal.
IF YOUR VACUUM CLEANER DOES NOT START
• The appliance is not powered: make sure the appliance is properly connected.
IF YOUR VACUUM CLEANER DOES NOT SUCK
• An accessory or the hose is blocked: unblock the accessory or hose.
• The lid is not properly closed: check that the bag is properly in position and close the lid.
IF YOUR VACUUM CLEANER IS NOT SUCKING PROPERLY OR IS MAKING A WHISTLING NOISE
• An accessory or the hose is partially blocked: unblock the accessory or hose.
• The bag is full or saturated by fine dust: replace the paper bag (17a), or empty the textile bag * (17b).
• The bag full light is red: the filtration system is saturated.
- HEPA cassette*: change the HEPA cassette * (14a) (ref. ZR0041 01) and replace it in its housing or
wash the HEPA filter cassette* (14b) (ref. ZR0042 01) according to the procedure.
- Microfilter*: Remove the microfilter* and replace it with a new one (ref. ZR0039 01).
• The electronic power regulator* is in the minimum position: increase the power using the
electronic power regulator* (unless you are cleaning fragile fabrics).
• The mechanical power regulator on the grip is open: close the mechanical power regulator.
* According to model: these systems are specific to certain models or are accessories available as an option.
To Next Page
Loading...
Need help?
General
