Ryobi P553 User Manual

OPERATOR’S MANUAL
MANUEL D’UTILISATION
MANUAL DEL OPERADOR
7-1/4 in., 18 VOLT MITER SAW
SCIE À ONGLETS DE 184 mm
(7-1/4 po), 18 V
SIERRA INGLETEADORA
DE 184 mm (7-1/4 pulg.), 18 V
P553
WARNING: To reduce the
risk of injury, the user must read and
understand the operator’s manual
before using this product.
SAVE THIS MANUAL FOR
FUTURE REFERENCE
ADVERTENCIA: Para reducir
el riesgo de lesiones, el usuario debe leer
y comprender el manual del operador
antes de usar este producto.
AVERTISSEMENT : Pour
réduire les risques de blessures,
l’utilisateur doit lire et veiller à bien
comprendre le manuel d’utilisation avant
d’employer ce produit.
GUARDE ESTE MANUAL
PARA FUTURAS CONSULTAS
CONSERVER CE MANUEL
POUR FUTURE RÉFÉRENCE
TABLE OF CONTENTS
****************
 General Safety Rules .......................2-3
 Miter Saw Safety Rules ...................3-4
 Additional Safety Rules ...................4-5
 Symbols ..............................................6
 Glossary of Terms ...............................7
 Features .........................................8-10
 Tools Needed ...................................10
 Loose Parts List ................................11
 Assembly .....................................11-18
 Operation .....................................18-26
 Adjustments .....................................27
 Maintenance ..................................... 28
 Parts Ordering / Service ..... Back Page
TABLE DES MATIÈRES
****************
 Règles de sécurité générales ..........2-3
 Règles de sécurité scie à onglets ....3-4
 Règles de sécurité supplémentaires ...4-5
 Symboles ............................................6
 Glossaire .............................................7
 Caractéristiques ............................8-10
 Outils nécessaires ............................10
 Liste des pièces détachées ..............11
 Assemblage .................................11-18
 Utilisation .....................................18-26
 Réglages ...........................................27
 Entretien ...........................................28
 Commande de pièces /
réparation ..........................Page arrière
ÍNDICE DE CONTENIDO
****************
 Reglas de seguridad generales .......2-3
 Reglas de seguridad sierra
ingleteadora ....................................3-4
Advertencias de seguridad
adicionales ......................................4-5
 Símbolos ............................................6
 Glosario de términos ..........................7
 Características ..............................8-10
 Herramientas necesarias ..................10
 Lista de piezas sueltas .....................11
 Armado ........................................11-18
 Funcionamiento ...........................18-26
 Ajustes ..............................................27
 Mantenimiento ..................................28
 Pedidos de piezas /
servicio .......................... Pág. posterior

Ryobi P553 Specifications

General

Brand	Ryobi
Model	P553
Category	Saw
Language	English

Summary

General Safety Rules

Work Area Safety

Keep the work area clean and well-lit to prevent accidents.

Electrical Safety

Guidelines for safe use of electrical components and preventing shock.

Personal Safety

Rules for user alertness, PPE, and avoiding distractions during operation.

Power Tool Use and Care

Proper usage, maintenance, and handling of the power tool to ensure safety.

Battery Tool Use and Care

Safe practices for charging, handling, and storing battery packs.

Miter Saw Specific Safety Rules

Safety precautions unique to operating a miter saw.

Additional Safety Rules

Further safety guidelines and precautions for using the tool.

Symbols

Signal Words

Explains the meaning and risk levels associated with DANGER, WARNING, CAUTION, and NOTICE.

Product Symbols

Defines common symbols used on the product for safe operation.

Features

Product Specifications

Details the technical specifications of the miter saw, including dimensions and capacity.

Saw Components Overview

Identifies and describes key parts like the blade, guards, and locking mechanisms.

Miter and Bevel Adjustment Features

Explains the miter/bevel lock knobs and table/arm adjustment mechanisms.

Workpiece Support and Safety Features

Details the miter fence, sliding fence, and work clamp for workpiece security.

Operational Features

Covers positive stops, self-retracting guards, and switch mechanisms.

Tools Needed for Adjustments

Lists necessary tools for performing maintenance and adjustments.

Assembly

Unpacking and Initial Inspection

Steps for safely unpacking and inspecting the miter saw after shipping.

Mounting the Miter Saw

Instructions on how to securely mount the saw to a workbench or stand.

Installing Key Components

Guides on attaching lock knobs, rear bracket, and dust bag for proper function.

Blade Installation and Replacement

Procedures for safely installing or replacing the saw blade.

Throat Plate and Blade Alignment

Steps for throat plate replacement and initial blade-to-fence squaring.

Squaring Blade to Miter Table

Procedure to align the saw blade perpendicular to the miter table for accuracy.

Operation

Applications of the Miter Saw

Lists the intended uses and materials for the compound miter saw.

Battery Pack Installation and Removal

Steps for inserting and removing the battery pack for safe operation.

Basic Cutting Procedures

General safety and operational guidelines for cutting operations.

Miter and Cross Cutting

Instructions for performing standard miter and cross cuts with the saw.

Bevel Cutting

Detailed steps for making bevel cuts with the saw at various angles.

Compound Miter Cutting

Guidance on performing cuts with both miter and bevel angles simultaneously.

Supporting Long Workpieces

Methods for providing adequate support for long materials during cuts.

Advanced Cutting Techniques

Provides charts and techniques for compound and crown molding cuts.

Cutting Warped Material

Guidelines for safely cutting warped or bowed workpieces to prevent kickback.

Adjustments

Pivot Adjustments

Information on pivot joints and their factory settings for arm movement.

Positive Stop Adjustments

Procedures for adjusting positive stops for specific bevel and miter angles.

Maintenance

General Maintenance and Cleaning

Cleaning procedures and precautions for maintaining the tool's plastic parts.

Lubrication Requirements

Information on the tool's lubrication and bearing maintenance.