EasyManua.ls Logo

Ryobi P620 - User Manual

Ryobi P620
158 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
GB
18 VOLT SPEED SPRAYER
USER’S MANUAL 1
FR
PISTOLET À PEINTURE 18 VOLT MANUEL D’UTILISATION 7
DE
18 VOLT HOCHGESCHWINDIGKEITS SPRÜHPISTOLE
BEDIENUNGSANLEITUNG 13
ES
PULVERIZADOR “SPEED SPRAYER” DE 18 VOLTIOS MANUAL DE UTILIZACIÓN 19
IT
SPRUZZATORE DA 18 VOLT MANUALE D’USO
25
NL
18 VOLT VERFSPUIT
GEBRUIKERSHANDLEIDING 31
PT
PULVERIZADOR DE VELOCIDADE DE 18 VOLT MANUAL DE UTILIZAÇÃO 37
DK
18 V LYNMALERPRØJTE BRUGERVEJLEDNING 43
SE
18 VOLT SNABBFÄRGPISTOL INSTRUKTIONSBOK 49
FI
18 VOLTIN PIKASUMUTIN KÄYTTÄJÄN KÄSIKIRJA 55
NO
18 VOLT HURTIGSPRØYTE BRUKSANVISNING 61
RU
СКОРОСТНОЙ РАСПЫЛИТЕЛЬ, 18 В êìäéÇéÑëíÇé èé ùäëèãìÄíÄñàà 67
PL
PISTOLET NATRYSKOWY 18 V INSTRUKCJA OBSŁUGI 73
CZ
18 VOLTOVÁ ROZPRAŠOVACÍ PISTOLE NÁVOD K OBSLUZE 79
HU
18 VOLTOS FESTÉKSZÓRÓ HASZNÁLATI ÚTMUTATÓ 85
RO
PULVERIZATOR RAPID 18 VOLŢI MANUAL DE UTILIZARE 91
LV
18 V KRĀSU PISTOLE LIETOTĀJA ROKASGRĀMATA 97
LT
18 VOLTŲ PURKŠTUVAS NAUDOJIMO VADOVAS 103
EE
KIIR-VÄRVIPRITS 18 VOLTI KASUTAJAJUHEND 109
HR
RASPRŠIVAČ OD 18 V KORISNI»KI PRIRU»NIK 115
SI
18 VOLTNI HITRI RAZPRŠILNIK UPORABNIŠKI PRIROČNIK 121
SK
18 VOLTOVÝ RÝCHLY SPREJOVAČ NÁVOD NA POUŽITIE 127
GR
ΨΕΚΑΣΤΗΡΑΣ ΤΑΧΥΤΗΤΑΣ 18 VOLT ΟΔΗΓΙΕΣ ΧΡΗΣΗΣ 133
TR
18 VOLT BOYA TABANCASI KULLANiM KILAVUZU 139
P620
GB ORIGINAL INSTRUCTIONS FR TRADUCTION DES INSTRUCTIONS ORIGINALES DE ÜBERSETZUNG DER ORIGINALANLEITUNG ES TRADUCCIÓN
DE LAS INSTRUCCIONES ORIGINALES IT TRADUZIONE DELLE ISTRUZIONI ORIGINALI NL VERTALING VAN DE ORIGINELE INSTRUCTIES PT TRADUÇÃO
DAS INSTRUÇÕES ORIGINAIS DK OVERSÆTTELSE AF DE ORIGINALE INSTRUKTIONER SE ÖVERSÄTTNING AV DE URSPRUNGLIGA INSTRUKTIONERNA
FI
ALKUPERÄISTEN OHJEIDEN SUOMENNOS NO OVERSETTELSE AV DE ORIGINALE INSTRUKSJONENE RU ПЕРЕВОД ОРИГИНАЛЬНЫХ ИНСТРУКЦИЙ PL TŁUMACZENIE
INSTRUKCJI ORYGINALNEJ CZ PŘEKLAD ORIGINÁLNÍCH POKYNŮ HU AZ EREDETI ÚTMUTATÓ FORDÍTÁSA RO TRADUCEREA INSTRUCŢIUNILOR ORIGINALE LV TULKOTS NO
ORIĢINĀLĀS INSTRUKCIJAS LT ORIGINALIŲ INSTRUKCIJŲ VERTIMAS EE ORIGINAALJUHENDI TÕLGE HR PRIJEVOD ORIGINALNIH UPUTA SI PREVOD ORIGINALNIH NAVODIL SK
PREKLAD POKYNOV V ORIGINÁLI GR ΜΕΤΑΦΡΑΣΗ ΤΩΝ ΠΡΩΤΟΤΥΠΩΝ ΟΔΗΓΙΩΝ TR ORIJINAL TALIMATLARIN TERCÜMESI

Table of Contents

Questions and Answers

  • J
    Jonathan BaileySep 4, 2025
    What to do if Ryobi P620 motor runs but doesn't spray?
    • J
      John TrujilloSep 4, 2025
      If the Ryobi Paint Sprayer motor seems to be running properly but doesn’t spray, several issues could be the cause. First, check if the suction tube and filter are damaged and reinstall or replace them if needed. A clogged or worn-out atomizer valve can also prevent spraying, so clean or replace it. If the material you're spraying is too thick, follow the manufacturer’s directions to thin it. Lastly, a plugged spray tip or intake piston can be the culprit; thoroughly clean the sprayer and replace the piston if necessary, following the storage cleaning instructions.
  • O
    oryanSep 18, 2025
    Why is Ryobi Paint Sprayer leaking behind the spray tip?
    • N
      Natasha SilvaSep 18, 2025
      If the Ryobi Paint Sprayer is leaking paint or stain behind the spray tip, it could be due to a loose spray tip. Try tightening it. Alternatively, the atomizer valve might be worn or not properly positioned, in which case you should replace or reposition it as needed.
  • D
    Danielle LoganSep 16, 2025
    Why is Ryobi P620 Paint Sprayer spitting or globbing?
    • M
      mark10Sep 16, 2025
      If the sprayed material from your Ryobi Paint Sprayer is spitting or globbing up, several factors could be responsible. Check if the paint container volume is getting low and refill it. Ensure that the material you're spraying isn't too thick by following the manufacturer's directions to thin it as needed. Also, make sure the suction tube is securely installed. A clogged or worn-out atomizer valve can also cause this issue, so clean or replace it. Finally, inspect the spray tip or piston for wear and clean or replace them if necessary.
  • T
    Thomas BaileySep 14, 2025
    Why does my Ryobi Paint Sprayer motor overheat?
    • M
      Makayla GonzalezSep 14, 2025
      Your Ryobi Paint Sprayer motor might overheat because the piston has seized up. Thoroughly clean the sprayer using the long-term storage cleaning instructions in the Maintenance section of this manual. Also, release the trigger at the end of each pass to allow the motor to cool.
  • K
    Kevin MartinSep 12, 2025
    What to do if Ryobi P620 Paint Sprayer is leaking behind the spray tip?
    • L
      Luis BensonSep 12, 2025
      If paint is leaking behind the spray tip of your Ryobi Paint Sprayer: * Ensure the spray tip is tight; tighten it if it's loose. * The atomizer valve may be worn or not positioned properly; replace or reposition it as needed.
  • C
    Cynthia KlineSep 12, 2025
    Why is my Ryobi P620 Paint Sprayer spitting?
    • S
      Steven BrownSep 12, 2025
      Your Ryobi Paint Sprayer might be spitting due to several reasons: * The suction tube may be loose, so reinstall it securely. * The atomizer valve could be clogged or worn out; try cleaning or replacing it. * The spray tip or piston might be worn, requiring cleaning or replacement. * The material you're spraying might be too thick; follow the manufacturer's directions to thin it. * The paint container volume may be getting low; refill it.
  • B
    Becky MooreSep 9, 2025
    Why Ryobi Paint Sprayer motor has a low hum but does not spray?
    • S
      Stacey ZavalaSep 9, 2025
      If the Ryobi Paint Sprayer motor has a low hum but does not spray, it could be that the piston has seized up. In this case, thoroughly clean the sprayer using long term storage cleaning instructions.
  • N
    Nicole LewisSep 7, 2025
    What causes Ryobi P620 Paint Sprayer motor to overheat?
    • C
      Christopher KentSep 7, 2025
      If the motor overheats, it could be due to a couple of reasons. The piston might have seized up; in this case, thoroughly clean the sprayer using long term storage cleaning instructions. Alternatively, continuous spray operation can cause overheating; release the trigger at the end of each pass to allow the motor to cool.
  • J
    jessica41Sep 5, 2025
    What to do if Ryobi P620 hums but doesn't spray?
    • L
      lowelisaSep 5, 2025
      If the Ryobi Paint Sprayer motor has a low hum but does not spray, the piston may have seized up. Thoroughly clean the sprayer using the long term storage cleaning instructions.
  • O
    Omar ReyesAug 20, 2025
    Why Ryobi Paint Sprayer motor seems to be running properly but doesn’t spray?
    • S
      Sean SmithAug 20, 2025
      If the motor seems to be running properly but the Ryobi Paint Sprayer isn’t spraying, several issues could be the cause. The suction tube and filter might be damaged, so reinstall or replace them as needed. The atomizer valve might be clogged or worn out, so clean or replace it. The material being sprayed might be too thick, so follow the manufacturer’s directions and thin the material as needed. Also, the spray tip or intake filter might be plugged, or the piston might be worn; in that case, thoroughly clean the sprayer and, if necessary, replace the piston, using storage cleaning instructions.

Summary

Special Safety Rules

Ear Protection and Handle Use

Insulated Grip Safety

Avoid electric shock by gripping insulated surfaces.

Operation: Battery Features

Battery Protection Features

Features protecting lithium-ion cells and maximizing battery life.

Preparing for Operation

Surface Prep & Material Thinning

Prepare surfaces and thin paint using viscosity cup for best results.

Ideal Viscosity Guidelines

Battery Pack Handling

Installation and Removal Procedures

Sprayer Operation

Filling Sprayer & Tip Selection

Fill sprayer, choose and adjust spray tip for desired pattern.

Spraying Technique & Pump Priming

Use steady strokes, maintain distance; prime pump before use.

Operation Continued

Cleaning After Use & Safety Warnings

Maintenance

Service Precautions & Storage Cleaning

Maintenance & Replacement

Preparing for Storage

Atomizer Valve Replacement

Valve Replacement Procedure

Ryobi P620 Specifications

General IconGeneral
TypeCordless
Flow Rate0.24 GPM
Battery18V
Nozzle Size0.015 in
Spray PatternVertical and Horizontal

Related product manuals