Ryobi PCL430 - Multi-Tool Safety Warnings; General Multi-Tool Safety; Symbols; Features

MULTI-TOOL SAFETY WARNINGS
Hold the powertoolby insulated gripping surfaces, when will reduce the risk of electric shock, fire, or serious personal
Performing an operation where the cutting accessory injury.
may
contact
hidden
wiring.
Cutting
accessory
contacting
m
Do
not
place
battery
tools
or
their
batteries
near
fire
or
a
“live”
wire
may
make
exposed
metal
parts
of
the
power
heat.
This
will
reduce
the
risk
of
explosion
and
possibly
injury.
tool
“live”
and
could
give
the
operator
an
electric
shock.
E
Do
not
crisis
dip
or
damage
Billar)
pácic
Do
ndi
m
Useclampsoranotherpracticalwaytosecureandsupport
use
a
battery
pack
or
charger
that
has
been
dropped
the
workpiece
to
a
stable
platform.
Holding
the
work
by
or
received
a
sharp
blow.
A
damaged
battery
is
subject
hand
or
against
your
body
leaves
it
unstable
and
may
lead
to
explosion.
Properly
dispose
of
a
dropped
or
damaged
to
loss
of
control.
battery
immediately.
m
Know
your
power
tool.
Read
operator's
manual
care-
m
Batteries
can
explode
in
the
presence
of
a
source
of
fully.
Learn
its
applications
and
limitations,
as
well
as
ignition,
such
as
a
pilot
light.
To
reduce
the
risk
of
serious
the
specific
potential
hazards
related
to
this
power
tool.
personal
injury,
never
use
any
cordless
product
in
the
pres-
Following
this
rule
will
reduce
the
risk
of
electric
shock,
fre,
ence
of
open
flame.
An
exploded
battery
can
propel
debris.
or
serious
Injury.
and
chemicals.
If
exposed,
flush
with
water
immediately.
W
Always
woar
oyo
protection
with
side
shields
markedto
—
Do
not
charge
battery
tool
in
a
damp
or
wet
location.
‘comply
with
ANSIZB7.1
when
assembling
parts,
operating
Do
not
use,
store,
or
charge
battery
packs
or
products
the
tool,
or
pertorming
maintenance.
Following
this
rule
will
in
locations
where
the
temperature
is
less
than
50°F
or
reduce
the
risk
of
serious
personal
injury.
more
than
10°F.
Do
not
store
outside
or
in
vehicles.
®
Protect
your
lungs.
Wear
a
face
or
dust
mask
ifthe
op-
m
Under
extreme
usage
or
temperature
conditions,
battery
eration
is
dusty.
Following
this
rule
will
reduce
the
risk
of
leakage
may
occur.
If
liquid
comes
in
contact
with
your
serious
personal
injury.
skin,
wash
immediately
with
soap
and
water.
If
liquid
m
Protect
your
hearing.
Wear
hearing
protection
during
ex-
gets
into
your
eyes,
flush
them
with
clean
water
for
at
tended
periods
of
operation.
Following
this
rule will
reduce
least
10
minutes,
then
seekimmediatemedicalattention.
the
risk
of
serious
personal
injury.
Following
this
rule
will reduce
the
risk
of
serious
personal
m Battery tools do not have to be plugged into an electrical TU:
outlet; therefore, they are always in operating condition, — M Save these instructions. Refer to them frequently and use
Beaware
of
possiblehazards
whennotusingyourbattery
them
to
instruct
others
who
may
use
this
tool.
if
you
loan
tool
or
when
changing
accessories.
Following
this
rule
‘someone
this
tool,
loan
them
these
instructions
also.
4 — English
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL SIGNAL MEANING
A Indicates a hazardous situation, which, if not avoided, will result in death or
DANGER:
À WARNING:
. Indicates a hazardous situation, that, if not avoided, may result in minor or
A CAUTION: moderate injury.
serious injury.
Indicates a hazardous situation, which, if not avoided, could result in death or
serious injury.
(Without Safety Alert Symbol) Indicates information considered important, but
NOTICE:
not
related
to
a
potential
injury
(e.g.
messages
relating
to
property
damage)
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper inter-
pretation of these symbols will allow you to operate the product better and safer.
SYMBOL DESIGNATION/EXPLANATION
Always wear eye protection with side shields marked to comply with ANSI
287.1.
This product uses lithium-ion (Li-ion) batteries. Local, state or federal laws
may prohibit disposal of batteries in ordinary trash. Consult your local waste
authority for information regarding available recycling and/or disposal options.
PRODUCT SPECIFICATIONS
Speed (OPM)...
Oscillation...
10,000-20,000/min
3 degrees
— English